Skip to content
Log In

PCI-DSS v4.0 Control Baseline for Red Hat Enterprise Linux 9

Rules and Groups employed by this XCCDF Profile

  • System Settings

    Contains rules that check correct system settings.
    Group
    Show

  • Installing and Maintaining Software

    The following sections contain information on security-relevant choices during the initial operating system installation process and the setup of software updates.
    Group
    Show

  • System and Software Integrity

    System and software integrity can be gained by installing antivirus, increasing system encryption strength with FIPS, verifying installed software, enabling SELinux, installing an Intrusion Prevent...
    Group
    Show

  • Software Integrity Checking

    Both the AIDE (Advanced Intrusion Detection Environment) software and the RPM package management system provide mechanisms for verifying the integrity of installed software. AIDE uses snapshots of ...
    Group
    Show

  • Verify Integrity with RPM

    The RPM package management system includes the ability to verify the integrity of installed packages by comparing the installed files with information about the files taken from the package metadat...
    Group
    Show

  • Verify File Hashes with RPM

    Without cryptographic integrity protections, system executables and files can be altered by unauthorized users without detection. The RPM package management system can check the hashes of installed...
    Rule High Severity
    Show

  • Verify and Correct Ownership with RPM

    The RPM package management system can check file ownership permissions of installed software packages, including many that are important to system security. After locating a file with incorrect per...
    Rule High Severity
    Show

  • Verify Integrity with AIDE

    AIDE conducts integrity checks by comparing information about files with previously-gathered information. Ideally, the AIDE database is created immediately after initial system configuration, and t...
    Group
    Show

  • Install AIDE

    The aide package can be installed with the following command: 
    $ sudo dnf install aide
    Rule Medium Severity
    Show

  • Build and Test AIDE Database

    Run the following command to generate a new database: <pre>$ sudo /usr/sbin/aide --init</pre> By default, the database will be written to the file <code>/var/lib/aide/aide.db.new.gz</code>. Sto...
    Rule Medium Severity
    Show

  • Configure Periodic Execution of AIDE

    At a minimum, AIDE should be configured to run a weekly scan. To implement a daily execution of AIDE at 4:05am using cron, add the following line to <code>/etc/crontab</code>: <pre>05 4 * * * root ...
    Rule Medium Severity
    Show

  • System Cryptographic Policies

    Linux has the capability to centrally configure cryptographic polices. The command <code>update-crypto-policies</code> is used to set the policy applicable for the various cryptographic back-ends, ...
    Group
    Show

  • Configure System Cryptography Policy

    To configure the system cryptography policy to use ciphers only from the <code><xccdf-1.2:sub idref="xccdf_org.ssgproject.content_value_var_system_crypto_policy" use="legacy"></xccdf-1.2:sub></code...
    Rule High Severity
    Show

  • Configure SSH to use System Crypto Policy

    Crypto Policies provide a centralized control over crypto algorithms usage of many packages. SSH is supported by crypto policy, but the SSH configuration may be set up to ignore it. To check that C...
    Rule Medium Severity
    Show

  • GNOME Desktop Environment

    GNOME is a graphical desktop environment bundled with many Linux distributions that allow users to easily interact with the operating system graphically rather than textually. The GNOME Graphical D...
    Group
    Show

  • Make sure that the dconf databases are up-to-date with regards to respective keyfiles

    By default, DConf uses a binary database as a data backend. The system-level database is compiled from keyfiles in the /etc/dconf/db/ directory by the <pre>dconf update</pre> command. More specific...
    Rule High Severity
    Show

  • Configure GNOME Login Screen

    In the default GNOME desktop, the login is displayed after system boot and can display user accounts, allow users to reboot the system, and allow users to login automatically and/or with a guest ac...
    Group
    Show

  • Disable GDM Automatic Login

    The GNOME Display Manager (GDM) can allow users to automatically login without user interaction or credentials. User should always be required to authenticate themselves to the system that they are...
    Rule High Severity
    Show

  • GNOME Media Settings

    GNOME media settings that apply to the graphical interface.
    Group
    Show

  • Disable GNOME3 Automounting

    The system's default desktop environment, GNOME3, will mount devices and removable media (such as DVDs, CDs and USB flash drives) whenever they are inserted into the system. To disable automount wi...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules