Skip to content
Log In

C2S for Red Hat Enterprise Linux 7

Rules and Groups employed by this XCCDF Profile

  • System Settings

    Contains rules that check correct system settings.
    Group
    Show

  • Installing and Maintaining Software

    The following sections contain information on security-relevant choices during the initial operating system installation process and the setup of software updates.
    Group
    Show

  • System and Software Integrity

    System and software integrity can be gained by installing antivirus, increasing system encryption strength with FIPS, verifying installed software, enabling SELinux, installing an Intrusion Prevent...
    Group
    Show

  • Disable Prelinking

    The prelinking feature changes binaries in an attempt to decrease their startup time. In order to disable it, change or add the following line inside the file <code>/etc/sysconfig/prelink</code>: <...
    Rule Medium Severity
    Show

  • Software Integrity Checking

    Both the AIDE (Advanced Intrusion Detection Environment) software and the RPM package management system provide mechanisms for verifying the integrity of installed software. AIDE uses snapshots of ...
    Group
    Show

  • Verify Integrity with AIDE

    AIDE conducts integrity checks by comparing information about files with previously-gathered information. Ideally, the AIDE database is created immediately after initial system configuration, and t...
    Group
    Show

  • Install AIDE

    The aide package can be installed with the following command: 
    $ sudo yum install aide
    Rule Medium Severity
    Show

  • Configure Periodic Execution of AIDE

    At a minimum, AIDE should be configured to run a weekly scan. To implement a daily execution of AIDE at 4:05am using cron, add the following line to <code>/etc/crontab</code>: <pre>05 4 * * * root ...
    Rule Medium Severity
    Show

  • Disk Partitioning

    To ensure separation and protection of data, there are top-level system directories which should be placed on their own physical partition or logical volume. The installer's default partitioning sc...
    Group
    Show

  • Ensure /home Located On Separate Partition

    If user home directories will be stored locally, create a separate partition for <code>/home</code> at installation time (or migrate it later using LVM). If <code>/home</code> will be mounted from ...
    Rule Low Severity
    Show

  • Ensure /tmp Located On Separate Partition

    The /tmp directory is a world-writable directory used for temporary file storage. Ensure it has its own partition or logical volume at installation time, or migrate it using LVM.
    Rule Low Severity
    Show

  • Ensure /var Located On Separate Partition

    The <code>/var</code> directory is used by daemons and other system services to store frequently-changing data. Ensure that <code>/var</code> has its own partition or logical volume at installation...
    Rule Low Severity
    Show

  • Ensure /var/log Located On Separate Partition

    System logs are stored in the /var/log directory. Ensure that /var/log has its own partition or logical volume at installation time, or migrate it using LVM.
    Rule Low Severity
    Show

  • Ensure /var/log/audit Located On Separate Partition

    Audit logs are stored in the <code>/var/log/audit</code> directory. Ensure that <code>/var/log/audit</code> has its own partition or logical volume at installation time, or migrate it using LVM. M...
    Rule Low Severity
    Show

  • Ensure /var/tmp Located On Separate Partition

    The /var/tmp directory is a world-writable directory used for temporary file storage. Ensure it has its own partition or logical volume at installation time, or migrate it using LVM.
    Rule Medium Severity
    Show

  • GNOME Desktop Environment

    GNOME is a graphical desktop environment bundled with many Linux distributions that allow users to easily interact with the operating system graphically rather than textually. The GNOME Graphical D...
    Group
    Show

  • Make sure that the dconf databases are up-to-date with regards to respective keyfiles

    By default, DConf uses a binary database as a data backend. The system-level database is compiled from keyfiles in the /etc/dconf/db/ directory by the <pre>dconf update</pre> command. More specific...
    Rule High Severity
    Show

  • Updating Software

    The <code>yum</code> command line tool is used to install and update software packages. The system also provides a graphical software update tool in the <b>System</b> menu, in the <b>Administration...
    Group
    Show

  • Ensure gpgcheck Enabled In Main yum Configuration

    The <code>gpgcheck</code> option controls whether RPM packages' signatures are always checked prior to installation. To configure yum to check package signatures before installing them, ensure the ...
    Rule High Severity
    Show

  • Ensure Red Hat GPG Key Installed

    To ensure the system can cryptographically verify base software packages come from Red Hat (and to connect to the Red Hat Network to receive them), the Red Hat GPG key must properly be installed. T...
    Rule High Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules