Skip to content
ATO Pathways
  Log In

C2S for Red Hat Enterprise Linux 7

Rules and Groups employed by this XCCDF Profile

  • Verify Permissions on cron.weekly

    To properly set the permissions of /etc/cron.weekly, run the command: 
    $ sudo chmod 0700 /etc/cron.weekly
    Rule Medium Severity
    Show

  • Verify Permissions on crontab

    To properly set the permissions of /etc/crontab, run the command: 
    $ sudo chmod 0600 /etc/crontab
    Rule Medium Severity
    Show

  • DHCP

    The Dynamic Host Configuration Protocol (DHCP) allows systems to request and obtain an IP address and other configuration parameters from a server....
    Group
    Show

  • Disable DHCP Server

    The DHCP server <code>dhcpd</code> is not installed or activated by default. If the software was installed and activated, but the system does not n...
    Group
    Show

  • Disable DHCP Service

    The <code>dhcpd</code> service should be disabled on any system that does not need to act as a DHCP server. The <code>dhcpd</code> service can be ...
    Rule Medium Severity
    Show

  • DNS Server

    Most organizations have an operational need to run at least one nameserver. However, there are many common attacks involving DNS server software, a...
    Group
    Show

  • Disable DNS Server

    DNS software should be disabled on any systems which does not need to be a nameserver. Note that the BIND DNS server software is not installed on R...
    Group
    Show

  • Disable named Service

    The named service can be disabled with the following command: 
    $ sudo systemctl mask --now named.service
    Rule Medium Severity
    Show

  • FTP Server

    FTP is a common method for allowing remote access to files. Like telnet, the FTP protocol is unencrypted, which means that passwords and other data...
    Group
    Show

  • Disable vsftpd if Possible

    To minimize attack surface, disable vsftpd if at all possible.
    Group
    Show

  • Disable vsftpd Service

    The vsftpd service can be disabled with the following command: 
    $ sudo systemctl mask --now vsftpd.service
    Rule Medium Severity
    Show

  • Web Server

    The web server is responsible for providing access to content via the HTTP protocol. Web servers represent a significant security risk because: <br...
    Group
    Show

  • Disable Apache if Possible

    If Apache was installed and activated, but the system does not need to act as a web server, then it should be disabled and removed from the system.
    Group
    Show

  • Disable httpd Service

    The httpd service can be disabled with the following command: 
    $ sudo systemctl mask --now httpd.service
    Rule Unknown Severity
    Show

  • IMAP and POP3 Server

    Dovecot provides IMAP and POP3 services. It is not installed by default. The project page at <a href="http://www.dovecot.org">http://www.dovec...
    Group
    Show

  • Disable Dovecot

    If the system does not need to operate as an IMAP or POP3 server, the dovecot software should be disabled and removed.
    Group
    Show

  • Disable Dovecot Service

    The dovecot service can be disabled with the following command: 
    $ sudo systemctl mask --now dovecot.service
    Rule Unknown Severity
    Show

  • LDAP

    LDAP is a popular directory service, that is, a standardized way of looking up information from a central database. Red Hat Enterprise Linux 7 incl...
    Group
    Show

  • Configure OpenLDAP Server

    This section details some security-relevant settings for an OpenLDAP server. Installation and configuration of OpenLDAP on Red Hat Enterprise Linu...
    Group
    Show

  • Uninstall openldap-servers Package

    The openldap-servers package is not installed by default on a Red Hat Enterprise Linux 7 system. It is needed only by the OpenLDAP server, not by t...
    Rule Low Severity
    Show

  • Mail Server Software

    Mail servers are used to send and receive email over the network. Mail is a very common service, and Mail Transfer Agents (MTAs) are obvious target...
    Group
    Show

  • Configure SMTP For Mail Clients

    This section discusses settings for Postfix in a submission-only e-mail configuration.
    Group
    Show

  • Disable Postfix Network Listening

    Edit the file <code>/etc/postfix/main.cf</code> to ensure that only the following <code>inet_interfaces</code> line appears: <pre>inet_interfaces =...
    Rule Medium Severity
    Show

  • NFS and RPC

    The Network File System is a popular distributed filesystem for the Unix environment, and is very widely deployed. This section discusses the circ...
    Group
    Show

  • Disable All NFS Services if Possible

    If there is not a reason for the system to operate as either an NFS client or an NFS server, follow all instructions in this section to disable sub...
    Group
    Show

  • Disable Services Used Only by NFS

    If NFS is not needed, disable the NFS client daemons nfslock, rpcgssd, and rpcidmapd. <br><br> All of these daemons run with elevated privileges, a...
    Group
    Show

  • Disable rpcbind Service

    The rpcbind utility maps RPC services to the ports on which they listen. RPC processes notify rpcbind when they start, registering the ports they a...
    Rule Low Severity
    Show

  • Configure NFS Clients

    The steps in this section are appropriate for systems which operate as NFS clients.
    Group
    Show

  • Disable NFS Server Daemons

    There is no need to run the NFS server daemons <code>nfs</code> and <code>rpcsvcgssd</code> except on a small number of properly secured systems de...
    Group
    Show

  • Disable Network File System (nfs)

    The Network File System (NFS) service allows remote hosts to mount and interact with shared filesystems on the local system. If the local system is...
    Rule Unknown Severity
    Show

  • Network Time Protocol

    The Network Time Protocol is used to manage the system clock over a network. Computer clocks are not very accurate, so time will drift unpredictabl...
    Group
    Show

  • Enable the NTP Daemon

    Run the following command to determine the current status of the <code>chronyd</code> service: <pre>$ sudo systemctl is-active chronyd</pre> If t...
    Rule Medium Severity
    Show

  • Obsolete Services

    This section discusses a number of network-visible services which have historically caused problems for system security, and for which disabling or...
    Group
    Show

  • Xinetd

    The <code>xinetd</code> service acts as a dedicated listener for some network services (mostly, obsolete ones) and can be used to provide access co...
    Group
    Show

  • Install tcp_wrappers Package

    When network services are using the <code>xinetd</code> service, the <code>tcp_wrappers</code> package should be installed. The <code>tcp_wrappers<...
    Rule Medium Severity
    Show

  • Disable xinetd Service

    The xinetd service can be disabled with the following command: 
    $ sudo systemctl mask --now xinetd.service
    Rule Medium Severity
    Show

  • NIS

    The Network Information Service (NIS), also known as 'Yellow Pages' (YP), and its successor NIS+ have been made obsolete by Kerberos, LDAP, and oth...
    Group
    Show

  • Remove NIS Client

    The Network Information Service (NIS), formerly known as Yellow Pages, is a client-server directory service protocol used to distribute system conf...
    Rule Unknown Severity
    Show

  • Uninstall ypserv Package

    The ypserv package can be removed with the following command: 
    $ sudo yum erase ypserv
    Rule High Severity
    Show

  • Rlogin, Rsh, and Rexec

    The Berkeley r-commands are legacy services which allow cleartext remote access and have an insecure trust model.
    Group
    Show

  • Uninstall rsh Package

    The rsh package contains the client commands for the rsh services
    Rule Unknown Severity
    Show

  • Disable rexec Service

    The <code>rexec</code> service, which is available with the <code>rsh-server</code> package and runs as a service through xinetd or separately as a...
    Rule High Severity
    Show

  • Disable rlogin Service

    The <code>rlogin</code> service, which is available with the <code>rsh-server</code> package and runs as a service through xinetd or separately as ...
    Rule High Severity
    Show

  • Disable rsh Service

    The <code>rsh</code> service, which is available with the <code>rsh-server</code> package and runs as a service through xinetd or separately as a s...
    Rule High Severity
    Show

  • Remove Rsh Trust Files

    The files <code>/etc/hosts.equiv</code> and <code>~/.rhosts</code> (in each user's home directory) list remote hosts and users that are trusted by ...
    Rule High Severity
    Show

  • Chat/Messaging Services

    The talk software makes it possible for users to send and receive messages across systems through a terminal session.
    Group
    Show

  • Uninstall talk-server Package

    The talk-server package can be removed with the following command: 
     $ sudo yum erase talk-server
    Rule Medium Severity
    Show

  • Uninstall talk Package

    The <code>talk</code> package contains the client program for the Internet talk protocol, which allows the user to chat with other users on differe...
    Rule Medium Severity
    Show

  • Telnet

    The telnet protocol does not provide confidentiality or integrity for information transmitted on the network. This includes authentication informat...
    Group
    Show

  • Remove telnet Clients

    The telnet client allows users to start connections to other systems via the telnet protocol.
    Rule Low Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules