Skip to content
Log In

CUSP - Common User Security Profile for Fedora Workstation

Rules and Groups employed by this XCCDF Profile

  • Disable NFS Server Daemons

    There is no need to run the NFS server daemons <code>nfs</code> and <code>rpcsvcgssd</code> except on a small number of properly secured systems designated as NFS servers. Ensure that these daemons...
    Group
    Show

  • Disable Network File System (nfs)

    The Network File System (NFS) service allows remote hosts to mount and interact with shared filesystems on the local system. If the local system is not designated as a NFS server then this service ...
    Rule Unknown Severity
    Show

  • Network Time Protocol

    The Network Time Protocol is used to manage the system clock over a network. Computer clocks are not very accurate, so time will drift unpredictably on unmanaged systems. Central time protocols can...
    Group
    Show

  • Disable chrony daemon from acting as server

    The <code>port</code> option in <code>/etc/chrony.conf</code> can be set to <code>0</code> to make chrony daemon to never open any listening port for server operation and to operate strictly in a c...
    Rule Low Severity
    Show

  • Disable network management of chrony daemon

    The cmdport option in /etc/chrony.conf can be set to 0 to stop chrony daemon from listening on the UDP port 323 for management connections made by chronyc.
    Rule Low Severity
    Show

  • Configure Time Service Maxpoll Interval

    The <code>maxpoll</code> should be configured to <xccdf-1.2:sub idref="xccdf_org.ssgproject.content_value_var_time_service_set_maxpoll" use="legacy"></xccdf-1.2:sub> in <code>/etc/ntp.conf</code> o...
    Rule Medium Severity
    Show

  • Ensure that chronyd is running under chrony user account

    chrony is a daemon which implements the Network Time Protocol (NTP). It is designed to synchronize system clocks across a variety of systems and use a source that is highly accurate. More informati...
    Rule Medium Severity
    Show

  • A remote time server for Chrony is configured

    <code>Chrony</code> is a daemon which implements the Network Time Protocol (NTP). It is designed to synchronize system clocks across a variety of systems and use a source that is highly accurate. M...
    Rule Medium Severity
    Show

  • Obsolete Services

    This section discusses a number of network-visible services which have historically caused problems for system security, and for which disabling or severely limiting the service has been the best a...
    Group
    Show

  • Uninstall rsync Package

    The rsyncd service can be used to synchronize files between systems over network links. The <code>rsync</code> package can be removed with the following command: <pre> $ sudo dnf remove rsync</pre>...
    Rule Medium Severity
    Show

  • Xinetd

    The <code>xinetd</code> service acts as a dedicated listener for some network services (mostly, obsolete ones) and can be used to provide access controls and perform some logging. It has been large...
    Group
    Show

  • Uninstall xinetd Package

    The xinetd package can be removed with the following command: 
    $ sudo dnf remove xinetd
    Rule Low Severity
    Show

  • NIS

    The Network Information Service (NIS), also known as 'Yellow Pages' (YP), and its successor NIS+ have been made obsolete by Kerberos, LDAP, and other modern centralized authentication services. NIS...
    Group
    Show

  • Remove NIS Client

    The Network Information Service (NIS), formerly known as Yellow Pages, is a client-server directory service protocol used to distribute system configuration files. The NIS client (<code>ypbind</cod...
    Rule Unknown Severity
    Show

  • Uninstall ypserv Package

    The ypserv package can be removed with the following command: 
    $ sudo dnf remove ypserv
    Rule High Severity
    Show

  • Rlogin, Rsh, and Rexec

    The Berkeley r-commands are legacy services which allow cleartext remote access and have an insecure trust model.
    Group
    Show

  • Uninstall rsh-server Package

    The rsh-server package can be removed with the following command: 
    $ sudo dnf remove rsh-server
    Rule High Severity
    Show

  • Uninstall rsh Package

    The rsh package contains the client commands for the rsh services
    Rule Unknown Severity
    Show

  • Chat/Messaging Services

    The talk software makes it possible for users to send and receive messages across systems through a terminal session.
    Group
    Show

  • Uninstall talk-server Package

    The talk-server package can be removed with the following command: 
     $ sudo dnf remove talk-server
    Rule Medium Severity
    Show

  • Uninstall talk Package

    The <code>talk</code> package contains the client program for the Internet talk protocol, which allows the user to chat with other users on different systems. Talk is a communication program which ...
    Rule Medium Severity
    Show

  • Telnet

    The telnet protocol does not provide confidentiality or integrity for information transmitted on the network. This includes authentication information such as passwords. Organizations which use tel...
    Group
    Show

  • Uninstall telnet-server Package

    The telnet-server package can be removed with the following command: 
    $ sudo dnf remove telnet-server
    Rule High Severity
    Show

  • Remove telnet Clients

    The telnet client allows users to start connections to other systems via the telnet protocol.
    Rule Low Severity
    Show

  • TFTP Server

    TFTP is a lightweight version of the FTP protocol which has traditionally been used to configure networking equipment. However, TFTP provides little security, and modern versions of networking oper...
    Group
    Show

  • Uninstall tftp-server Package

    The tftp-server package can be removed with the following command: 
     $ sudo dnf remove tftp-server
    Rule High Severity
    Show

  • Remove tftp Daemon

    Trivial File Transfer Protocol (TFTP) is a simple file transfer protocol, typically used to automatically transfer configuration or boot files between systems. TFTP does not support authentication ...
    Rule Low Severity
    Show

  • Proxy Server

    A proxy server is a very desirable target for a potential adversary because much (or all) sensitive data for a given infrastructure may flow through it. Therefore, if one is required, the system ac...
    Group
    Show

  • Disable Squid if Possible

    If Squid was installed and activated, but the system does not need to act as a proxy server, then it should be disabled and removed.
    Group
    Show

  • Uninstall squid Package

    The squid package can be removed with the following command: 
     $ sudo dnf remove squid
    Rule Unknown Severity
    Show

  • Samba(SMB) Microsoft Windows File Sharing Server

    When properly configured, the Samba service allows Linux systems to provide file and print sharing to Microsoft Windows systems. There are two software packages that provide Samba support. The firs...
    Group
    Show

  • Disable Samba if Possible

    Even after the Samba server package has been installed, it will remain disabled. Do not enable this service unless it is absolutely necessary to provide Microsoft Windows file and print sharing fun...
    Group
    Show

  • Uninstall Samba Package

    The samba package can be removed with the following command: 
     $ sudo dnf remove samba
    Rule Unknown Severity
    Show

  • SNMP Server

    The Simple Network Management Protocol allows administrators to monitor the state of network devices, including computers. Older versions of SNMP were well-known for weak security, such as plaintex...
    Group
    Show

  • Disable SNMP Server if Possible

    The system includes an SNMP daemon that allows for its remote monitoring, though it not installed by default. If it was installed and activated but is not needed, the software should be disabled an...
    Group
    Show

  • Uninstall net-snmp Package

    The net-snmp package provides the snmpd service. The net-snmp package can be removed with the following command: 
    $ sudo dnf remove net-snmp
    Rule Unknown Severity
    Show

  • SSH Server

    The SSH protocol is recommended for remote login and remote file transfer. SSH provides confidentiality and integrity for data exchanged between two systems, as well as server authentication, throu...
    Group
    Show

  • Verify Group Who Owns SSH Server config file

    To properly set the group owner of /etc/ssh/sshd_config, run the command: 
    $ sudo chgrp root /etc/ssh/sshd_config
    Rule Medium Severity
    Show

  • Verify Owner on SSH Server config file

    To properly set the owner of /etc/ssh/sshd_config, run the command: 
    $ sudo chown root /etc/ssh/sshd_config
    Rule Medium Severity
    Show

  • Verify Permissions on SSH Server config file

    To properly set the permissions of /etc/ssh/sshd_config, run the command: 
    $ sudo chmod 0600 /etc/ssh/sshd_config
    Rule Medium Severity
    Show

  • Verify Permissions on SSH Server Private *_key Key Files

    SSH server private keys - files that match the <code>/etc/ssh/*_key</code> glob, have to have restricted permissions. If those files are owned by the <code>root</code> user and the <code>root</code...
    Rule Medium Severity
    Show

  • Verify Permissions on SSH Server Public *.pub Key Files

    To properly set the permissions of /etc/ssh/*.pub, run the command: 
    $ sudo chmod 0644 /etc/ssh/*.pub
    Rule Medium Severity
    Show

  • Configure OpenSSH Server if Necessary

    If the system needs to act as an SSH server, then certain changes should be made to the OpenSSH daemon configuration file <code>/etc/ssh/sshd_config</code>. The following recommendations can be app...
    Group
    Show

  • Set SSH Client Alive Count Max to zero

    The SSH server sends at most <code>ClientAliveCountMax</code> messages during a SSH session and waits for a response from the SSH client. The option <code>ClientAliveInterval</code> configures time...
    Rule Medium Severity
    Show

  • Set SSH Client Alive Count Max

    The SSH server sends at most <code>ClientAliveCountMax</code> messages during a SSH session and waits for a response from the SSH client. The option <code>ClientAliveInterval</code> configures time...
    Rule Medium Severity
    Show

  • Set SSH Client Alive Interval

    SSH allows administrators to set a network responsiveness timeout interval. After this interval has passed, the unresponsive client will be automatically logged out. <br> <br> To set this t...
    Rule Medium Severity
    Show

  • Disable Host-Based Authentication

    SSH's cryptographic host-based authentication is more secure than <code>.rhosts</code> authentication. However, it is not recommended that hosts unilaterally trust one another, even within an organ...
    Rule Medium Severity
    Show

  • Disable SSH Access via Empty Passwords

    Disallow SSH login with empty passwords. The default SSH configuration disables logins with empty passwords. The appropriate configuration is used if no value is set for <code>PermitEmptyPasswords<...
    Rule High Severity
    Show

  • Disable GSSAPI Authentication

    Unless needed, SSH should not permit extraneous or unnecessary authentication mechanisms like GSSAPI. <br> The default SSH configuration disallows authentications based on GSSAPI. The appropriate c...
    Rule Medium Severity
    Show

  • Disable Kerberos Authentication

    Unless needed, SSH should not permit extraneous or unnecessary authentication mechanisms like Kerberos. <br> The default SSH configuration disallows authentication validation through Kerberos. The ...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules