Skip to content
Log In

DRAFT - CIS Red Hat Enterprise Linux 10 Benchmark for Level 2 - Workstation

Rules and Groups employed by this XCCDF Profile

  • firewalld

    The dynamic firewall daemon <code>firewalld</code> provides a dynamically managed firewall with support for network “zones” to assign a level of trust to a network and its associated connections an...
    Group
    Show

  • Inspect and Activate Default firewalld Rules

    Firewalls can be used to separate networks into different zones based on the level of trust the user has decided to place on the devices and traffic within that network. <code>NetworkManager</code>...
    Group
    Show

  • Install firewalld Package

    The firewalld package can be installed with the following command: 
    $ sudo dnf install firewalld
    Rule Medium Severity
    Show

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in configuration files under the <code>/etc/firewalld/services</code> and <code>...
    Group
    Show

  • Configure Firewalld to Restrict Loopback Traffic

    Configure <code>firewalld</code> to restrict loopback traffic to the <code>lo</code> interface. The loopback traffic must be trusted by assigning the <code>lo</code> interface to the <code>firewal...
    Rule Medium Severity
    Show

  • Configure Firewalld to Trust Loopback Traffic

    Assign loopback interface to the <code>firewalld</code> <code>trusted</code> zone in order to explicitly allow the loopback traffic in the system. To configure <code>firewalld</code> to t...
    Rule Medium Severity
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the number of available addresses. Another important featu...
    Group
    Show

  • Configure IPv6 Settings if Necessary

    A major feature of IPv6 is the extent to which systems implementing it can automatically configure their networking devices using information from the network. From a security perspective, manually...
    Group
    Show

  • Configure Accepting Router Advertisements on All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.all.accept_ra=0</pre> To make sure that th...
    Rule Medium Severity
    Show

  • Disable Accepting ICMP Redirects for All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.all.accept_redirects=0</pre> To mak...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on all IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.all.accept_source_route=0</pre> ...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for IPv6 Forwarding

    To set the runtime status of the <code>net.ipv6.conf.all.forwarding</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.all.forwarding=0</pre> To make sure that ...
    Rule Medium Severity
    Show

  • Disable Accepting Router Advertisements on all IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.default.accept_ra=0</pre> To make sure...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.default.accept_redirects=0</pre...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.default.accept_source_route=...
    Rule Medium Severity
    Show

  • Kernel Parameters Which Affect Networking

    The sysctl utility is used to set parameters which affect the operation of the Linux kernel. Kernel parameters which affect networking and have security implications are described here.
    Group
    Show

  • Network Related Kernel Runtime Parameters for Hosts and Routers

    Certain kernel parameters should be set for systems which are acting as either hosts or routers to improve the system's ability defend against certain types of IPv4 protocol attacks.
    Group
    Show

  • Disable Accepting ICMP Redirects for All IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.accept_redirects=0</pre> To mak...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.accept_source_route=0</pre> ...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Log Martian Packets on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.log_martians</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.log_martians=1</pre> To make sure t...
    Rule Unknown Severity
    Show

  • Enable Kernel Parameter to Use Reverse Path Filtering on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.rp_filter</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.rp_filter=1</pre> To make sure that th...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Secure ICMP Redirects on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.secure_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.secure_redirects=0</pre> To mak...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.accept_redirects=0</pre...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.accept_source_route=...
    Rule Medium Severity
    Show

  • Enable Kernel Paremeter to Log Martian Packets on all IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.log_martians</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.log_martians=1</pre> To mak...
    Rule Unknown Severity
    Show

  • Enable Kernel Parameter to Use Reverse Path Filtering on all IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.rp_filter</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.rp_filter=1</pre> To make sure...
    Rule Medium Severity
    Show

  • Configure Kernel Parameter for Accepting Secure Redirects By Default

    To set the runtime status of the <code>net.ipv4.conf.default.secure_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.secure_redirects=0</pre...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Ignore ICMP Broadcast Echo Requests on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.icmp_echo_ignore_broadcasts</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.icmp_echo_ignore_broadcasts=1</pre> To...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Ignore Bogus ICMP Error Responses on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.icmp_ignore_bogus_error_responses</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.icmp_ignore_bogus_error_response...
    Rule Unknown Severity
    Show

  • Enable Kernel Parameter to Use TCP Syncookies on Network Interfaces

    To set the runtime status of the <code>net.ipv4.tcp_syncookies</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.tcp_syncookies=1</pre> To make sure that the settin...
    Rule Medium Severity
    Show

  • Network Parameters for Hosts Only

    If the system is not going to be used as a router, then setting certain kernel parameters ensure that the host will not perform routing of network traffic.
    Group
    Show

  • Disable Kernel Parameter for Sending ICMP Redirects on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.send_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.send_redirects=0</pre> To make su...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Sending ICMP Redirects on all IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.send_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.send_redirects=0</pre> To...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for IP Forwarding on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.ip_forward</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.ip_forward=0</pre> To make sure that the setting is per...
    Rule Medium Severity
    Show

  • nftables

    <code>If firewalld or iptables are being used in your environment, please follow the guidance in their respective section and pass-over the guidance in this section.</code><br><br> nftables is a su...
    Group
    Show

  • Install nftables Package

    nftables provides a new in-kernel packet classification framework that is based on a network-specific Virtual Machine (VM) and a new nft userspace command line tool. nftables reuses the existing Ne...
    Rule Medium Severity
    Show

  • Verify nftables Service is Disabled

    nftables is a subsystem of the Linux kernel providing filtering and classification of network packets/datagrams/frames and is the successor to iptables. The <code>nftables</code> service can be dis...
    Rule Medium Severity
    Show

  • Uncommon Network Protocols

    The system includes support for several network protocols which are not commonly used. Although security vulnerabilities in kernel networking code are not frequently discovered, the consequences ca...
    Group
    Show

  • Disable DCCP Support

    The Datagram Congestion Control Protocol (DCCP) is a relatively new transport layer protocol, designed to support streaming media and telephony. To configure the system to prevent the <code>dccp</...
    Rule Medium Severity
    Show

  • Disable RDS Support

    The Reliable Datagram Sockets (RDS) protocol is a transport layer protocol designed to provide reliable high-bandwidth, low-latency communications between nodes in a cluster. To configure the syst...
    Rule Low Severity
    Show

  • Disable SCTP Support

    The Stream Control Transmission Protocol (SCTP) is a transport layer protocol, designed to support the idea of message-oriented communication, with several streams of messages within one connection...
    Rule Medium Severity
    Show

  • Disable TIPC Support

    The Transparent Inter-Process Communication (TIPC) protocol is designed to provide communications between nodes in a cluster. To configure the system to prevent the <code>tipc</code> kernel module...
    Rule Low Severity
    Show

  • Wireless Networking

    Wireless networking, such as 802.11 (WiFi) and Bluetooth, can present a security risk to sensitive or classified systems and networks. Wireless networking hardware is much more likely to be include...
    Group
    Show

  • Disable Wireless Through Software Configuration

    If it is impossible to remove the wireless hardware from the device in question, disable as much of it as possible through software. The following methods can disable software support for wireless ...
    Group
    Show

  • Disable Bluetooth Service

    The bluetooth service can be disabled with the following command: 
    $ sudo systemctl mask --now bluetooth.service
    $ sudo service bluetooth stop
    Rule Medium Severity
    Show

  • File Permissions and Masks

    Traditional Unix security relies heavily on file and directory permissions to prevent unauthorized users from reading or modifying files to which they should not have access. <br> <br> Severa...
    Group
    Show

  • Verify Permissions on Important Files and Directories

    Permissions for many files on a system must be set restrictively to ensure sensitive information is properly protected. This section discusses important permission restrictions which can be verifie...
    Group
    Show

  • Verify that All World-Writable Directories Have Sticky Bits Set

    When the so-called 'sticky bit' is set on a directory, only the owner of a given file may remove that file from the directory. Without the sticky bit, any user with write access to a directory may ...
    Rule Medium Severity
    Show

  • Ensure No World-Writable Files Exist

    It is generally a good idea to remove global (other) write access to a file when it is discovered. However, check with documentation for specific applications before making changes. Also, monitor f...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules