Skip to content
ATO Pathways
  Log In

Standard System Security Profile for openEuler 22.03 LTS

Rules and Groups employed by this XCCDF Profile

  • Ensure Proper Configuration of Log Files

    The file <code>/etc/rsyslog.conf</code> controls where log message are written. These are controlled by lines called <i>rules</i>, which consist of...
    Group
    Show

  • Ensure cron Is Logging To Rsyslog

    Cron logging must be implemented to spot intrusions or trace cron job status. If <code>cron</code> is not logging to <code>rsyslog</code>, it can b...
    Rule Medium Severity
    Show

  • Ensure logging is configured

    The <code>/etc/rsyslog.conf</code> and <code>/etc/rsyslog.d/*.conf</code> files specifies rules for logging and which files are to be used to log c...
    Rule Medium Severity
    Show

  • Ensure remote access methods are monitored in Rsyslog

    Logging of remote access methods must be implemented to help identify cyber attacks and ensure ongoing compliance with remote access policies are b...
    Rule Medium Severity
    Show

  • Configure rsyslogd to Accept Remote Messages If Acting as a Log Server

    By default, <code>rsyslog</code> does not listen over the network for log messages. If needed, modules can be enabled to allow the rsyslog daemon t...
    Group
    Show

  • Enable rsyslog to Accept Messages via TCP, if Acting As Log Server

    The <code>rsyslog</code> daemon should not accept remote messages unless the system acts as a log server. If the system needs to act as a central l...
    Rule Unknown Severity
    Show

  • Enable rsyslog to Accept Messages via UDP, if Acting As Log Server

    The <code>rsyslog</code> daemon should not accept remote messages unless the system acts as a log server. If the system needs to act as a central l...
    Rule Unknown Severity
    Show

  • Network Configuration and Firewalls

    Most systems must be connected to a network of some sort, and this brings with it the substantial risk of network attack. This section discusses th...
    Group
    Show

  • firewalld

    The dynamic firewall daemon <code>firewalld</code> provides a dynamically managed firewall with support for network “zones” to assign a level of tr...
    Group
    Show

  • Ensure network interfaces are assigned to appropriate zone

    Firewall zones define the trust level of network connections or interfaces. Note: Changing firewall settings while connected over network can resul...
    Rule Medium Severity
    Show

  • Ensure Unnecessary Services and Ports Are Not Accepted

    Services and ports can be accepted or explicitly rejected or dropped by a zone. For every zone, a default behavior can be set that handles incoming...
    Rule Medium Severity
    Show

  • Inspect and Activate Default firewalld Rules

    Firewalls can be used to separate networks into different zones based on the level of trust the user has decided to place on the devices and traffi...
    Group
    Show

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • iptables and ip6tables

    A host-based firewall called <code>netfilter</code> is included as part of the Linux kernel distributed with the system. It is activated by default...
    Group
    Show

  • Inspect and Activate Default Rules

    View the currently-enforced <code>iptables</code> rules by running the command: <pre>$ sudo iptables -nL --line-numbers</pre> The command is analog...
    Group
    Show

  • Verify ip6tables Enabled if Using IPv6

    The ip6tables service can be enabled with the following command: 
    $ sudo systemctl enable ip6tables.service
    Rule Medium Severity
    Show

  • Verify iptables Enabled

    The iptables service can be enabled with the following command: 
    $ sudo systemctl enable iptables.service
    Rule Medium Severity
    Show

  • Set configuration for IPv6 loopback traffic

    Configure the loopback interface to accept traffic. Configure all other interfaces to deny traffic to the loopback network.
    Rule Medium Severity
    Show

  • Set configuration for loopback traffic

    Configure the loopback interface to accept traffic. Configure all other interfaces to deny traffic to the loopback network.
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in the configuration files <co...
    Group
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules