Skip to content
ATO Pathways
  Log In

Protection Profile for General Purpose Operating Systems

Rules and Groups employed by this XCCDF Profile

  • Inspect and Activate Default firewalld Rules

    Firewalls can be used to separate networks into different zones based on the level of trust the user has decided to place on the devices and traffi...
    Group
    Show

  • Install firewalld Package

    The firewalld package can be installed with the following command: 
    $ sudo yum install firewalld
    Rule Medium Severity
    Show

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the numb...
    Group
    Show

  • Configure IPv6 Settings if Necessary

    A major feature of IPv6 is the extent to which systems implementing it can automatically configure their networking devices using information from ...
    Group
    Show

  • Configure Accepting Router Advertisements on All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ip...
    Rule Medium Severity
    Show

  • Disable Accepting ICMP Redirects for All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on all IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl...
    Rule Medium Severity
    Show

  • Disable Accepting Router Advertisements on all IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w ne...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysct...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sy...
    Rule Medium Severity
    Show

  • Kernel Parameters Which Affect Networking

    The <code>sysctl</code> utility is used to set parameters which affect the operation of the Linux kernel. Kernel parameters which affect networking...
    Group
    Show

  • Network Related Kernel Runtime Parameters for Hosts and Routers

    Certain kernel parameters should be set for systems which are acting as either hosts or routers to improve the system's ability defend against cert...
    Group
    Show

  • Disable Accepting ICMP Redirects for All IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Log Martian Packets on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.log_martians</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net...
    Rule Unknown Severity
    Show

  • Enable Kernel Parameter to Use Reverse Path Filtering on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.rp_filter</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ip...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Secure ICMP Redirects on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.secure_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysct...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sy...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules