Skip to content
ATO Pathways
  Log In

DISA STIG for Red Hat Enterprise Linux 7

Rules and Groups employed by this XCCDF Profile

  • Uninstall telnet-server Package

    The telnet-server package can be removed with the following command: 
    $ sudo yum erase telnet-server
    Rule High Severity
    Show

  • TFTP Server

    TFTP is a lightweight version of the FTP protocol which has traditionally been used to configure networking equipment. However, TFTP provides littl...
    Group
    Show

  • Uninstall tftp-server Package

    The tftp-server package can be removed with the following command: 
     $ sudo yum erase tftp-server
    Rule High Severity
    Show

  • Ensure tftp Daemon Uses Secure Mode

    If running the Trivial File Transfer Protocol (TFTP) service is necessary, it should be configured to change its root directory at startup. To do s...
    Rule Medium Severity
    Show

  • SNMP Server

    The Simple Network Management Protocol allows administrators to monitor the state of network devices, including computers. Older versions of SNMP w...
    Group
    Show

  • Configure SNMP Server if Necessary

    If it is necessary to run the snmpd agent on the system, some best practices should be followed to minimize the security risk from the installation...
    Group
    Show

  • Ensure Default SNMP Password Is Not Used

    Edit <code>/etc/snmp/snmpd.conf</code>, remove or change the default community strings of <code>public</code> and <code>private</code>. This profil...
    Rule High Severity
    Show

  • SSH Server

    The SSH protocol is recommended for remote login and remote file transfer. SSH provides confidentiality and integrity for data exchanged between tw...
    Group
    Show

  • Install the OpenSSH Server Package

    The <code>openssh-server</code> package should be installed. The <code>openssh-server</code> package can be installed with the following command: <...
    Rule Medium Severity
    Show

  • Enable the OpenSSH Service

    The SSH server service, sshd, is commonly needed. The <code>sshd</code> service can be enabled with the following command: <pre>$ sudo systemctl e...
    Rule Medium Severity
    Show

  • Verify Permissions on SSH Server Private *_key Key Files

    SSH server private keys - files that match the <code>/etc/ssh/*_key</code> glob, have to have restricted permissions. If those files are owned by t...
    Rule Medium Severity
    Show

  • Verify Permissions on SSH Server Public *.pub Key Files

    To properly set the permissions of /etc/ssh/*.pub, run the command: 
    $ sudo chmod 0644 /etc/ssh/*.pub
    Rule Medium Severity
    Show

  • Configure OpenSSH Server if Necessary

    If the system needs to act as an SSH server, then certain changes should be made to the OpenSSH daemon configuration file <code>/etc/ssh/sshd_confi...
    Group
    Show

  • Set SSH Client Alive Count Max to zero

    The SSH server sends at most <code>ClientAliveCountMax</code> messages during a SSH session and waits for a response from the SSH client. The optio...
    Rule Medium Severity
    Show

  • Set SSH Client Alive Interval

    SSH allows administrators to set a network responsiveness timeout interval. After this interval has passed, the unresponsive client will be automat...
    Rule Medium Severity
    Show

  • Disable Host-Based Authentication

    SSH's cryptographic host-based authentication is more secure than <code>.rhosts</code> authentication. However, it is not recommended that hosts un...
    Rule Medium Severity
    Show

  • Allow Only SSH Protocol 2

    Only SSH protocol version 2 connections should be permitted. The default setting in <code>/etc/ssh/sshd_config</code> is correct, and can be verifi...
    Rule High Severity
    Show

  • Disable Compression Or Set Compression to delayed

    Compression is useful for slow network connections over long distances but can cause performance issues on local LANs. If use of compression is req...
    Rule Medium Severity
    Show

  • Disable SSH Access via Empty Passwords

    Disallow SSH login with empty passwords. The default SSH configuration disables logins with empty passwords. The appropriate configuration is used ...
    Rule High Severity
    Show

  • Disable GSSAPI Authentication

    Unless needed, SSH should not permit extraneous or unnecessary authentication mechanisms like GSSAPI. <br> The default SSH configuration disallows ...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules