Skip to content
ATO Pathways
  Log In

PCI-DSS v4 Control Baseline for SUSE Linux enterprise 15

Rules and Groups employed by this XCCDF Profile

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in configuration files under t...
    Group
    Show

  • Ensure firewall rules exist for all open ports

    Any ports that have been opened on non-loopback addresses need firewall rules to govern traffic.
    Rule Medium Severity
    Show

  • Set Default firewalld Zone for Incoming Packets

    To set the default zone to <code>drop</code> for the built-in default zone which processes incoming IPv4 and IPv6 packets, modify the following lin...
    Rule Medium Severity
    Show

  • iptables and ip6tables

    A host-based firewall called <code>netfilter</code> is included as part of the Linux kernel distributed with the system. It is activated by default...
    Group
    Show

  • Inspect and Activate Default Rules

    View the currently-enforced <code>iptables</code> rules by running the command: <pre>$ sudo iptables -nL --line-numbers</pre> The command is analog...
    Group
    Show

  • Set Default ip6tables Policy for Incoming Packets

    To set the default policy to DROP (instead of ACCEPT) for the built-in INPUT chain which processes incoming packets, add or correct the following l...
    Rule Medium Severity
    Show

  • Set configuration for IPv6 loopback traffic

    Configure the loopback interface to accept traffic. Configure all other interfaces to deny traffic to the loopback network.
    Rule Medium Severity
    Show

  • Set configuration for loopback traffic

    Configure the loopback interface to accept traffic. Configure all other interfaces to deny traffic to the loopback network.
    Rule Medium Severity
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the numb...
    Group
    Show

  • Configure IPv6 Settings if Necessary

    A major feature of IPv6 is the extent to which systems implementing it can automatically configure their networking devices using information from ...
    Group
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sy...
    Rule Medium Severity
    Show

  • Kernel Parameters Which Affect Networking

    The <code>sysctl</code> utility is used to set parameters which affect the operation of the Linux kernel. Kernel parameters which affect networking...
    Group
    Show

  • Network Related Kernel Runtime Parameters for Hosts and Routers

    Certain kernel parameters should be set for systems which are acting as either hosts or routers to improve the system's ability defend against cert...
    Group
    Show

  • Enable Kernel Parameter to Use Reverse Path Filtering on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.rp_filter</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ip...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Secure ICMP Redirects on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.secure_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysct...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Ignore ICMP Broadcast Echo Requests on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.icmp_echo_ignore_broadcasts</code> kernel parameter, run the following command: <pre>$ sudo sysctl ...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Ignore Bogus ICMP Error Responses on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.icmp_ignore_bogus_error_responses</code> kernel parameter, run the following command: <pre>$ sudo s...
    Rule Unknown Severity
    Show

  • Enable Kernel Parameter to Use TCP Syncookies on Network Interfaces

    To set the runtime status of the <code>net.ipv4.tcp_syncookies</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.t...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules