Skip to content
ATO Pathways
  Log In

PCI-DSS v4 Control Baseline for SUSE Linux enterprise 12

Rules and Groups employed by this XCCDF Profile

  • Ensure Logrotate Runs Periodically

    The <code>logrotate</code> utility allows for the automatic rotation of log files. The frequency of rotation is specified in <code>/etc/logrotate....
    Rule Medium Severity
    Show

  • Enable logrotate Timer

    The logrotate timer can be enabled with the following command: 
    $ sudo systemctl enable logrotate.timer
    Rule Medium Severity
    Show

  • Network Configuration and Firewalls

    Most systems must be connected to a network of some sort, and this brings with it the substantial risk of network attack. This section discusses th...
    Group
    Show

  • IPSec Support

    Support for Internet Protocol Security (IPsec) is provided with Libreswan.
    Group
    Show

  • Install strongswan Package

    The Strongswan package provides an implementation of IPsec and IKE, which permits the creation of secure tunnels over untrusted networks. The <code...
    Rule Medium Severity
    Show

  • iptables and ip6tables

    A host-based firewall called <code>netfilter</code> is included as part of the Linux kernel distributed with the system. It is activated by default...
    Group
    Show

  • Install iptables Package

    The iptables package can be installed with the following command: 
    $ sudo zypper install iptables
    Rule Medium Severity
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the numb...
    Group
    Show

  • Disable Support for IPv6 Unless Needed

    Despite configuration that suggests support for IPv6 has been disabled, link-local IPv6 address auto-configuration occurs even when only an IPv4 ad...
    Group
    Show

  • Ensure IPv6 is disabled through kernel boot parameter

    To disable IPv6 protocol support in the Linux kernel, add the argument <code>ipv6.disable=1</code> to the default GRUB2 command line for the Linux ...
    Rule Low Severity
    Show

  • Configure IPv6 Settings if Necessary

    A major feature of IPv6 is the extent to which systems implementing it can automatically configure their networking devices using information from ...
    Group
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sy...
    Rule Medium Severity
    Show

  • Kernel Parameters Which Affect Networking

    The <code>sysctl</code> utility is used to set parameters which affect the operation of the Linux kernel. Kernel parameters which affect networking...
    Group
    Show

  • Network Related Kernel Runtime Parameters for Hosts and Routers

    Certain kernel parameters should be set for systems which are acting as either hosts or routers to improve the system's ability defend against cert...
    Group
    Show

  • Enable Kernel Parameter to Use Reverse Path Filtering on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.rp_filter</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ip...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Secure ICMP Redirects on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.secure_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysct...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Ignore ICMP Broadcast Echo Requests on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.icmp_echo_ignore_broadcasts</code> kernel parameter, run the following command: <pre>$ sudo sysctl ...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Ignore Bogus ICMP Error Responses on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.icmp_ignore_bogus_error_responses</code> kernel parameter, run the following command: <pre>$ sudo s...
    Rule Unknown Severity
    Show

  • Enable Kernel Parameter to Use TCP Syncookies on Network Interfaces

    To set the runtime status of the <code>net.ipv4.tcp_syncookies</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.t...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules