Skip to content
ATO Pathways
  Log In

DISA STIG for Red Hat Enterprise Linux 9

Rules and Groups employed by this XCCDF Profile

  • Ensure rsyslog Does Not Accept Remote Messages Unless Acting As Log Server

    The <code>rsyslog</code> daemon should not accept remote messages unless the system acts as a log server. To ensure that it is not listening on the...
    Rule Medium Severity
    Show

  • Rsyslog Logs Sent To Remote Host

    If system logs are to be useful in detecting malicious activities, it is necessary to send logs to a remote server. An intruder who has compromised...
    Group
    Show

  • Ensure Logs Sent To Remote Host

    To configure rsyslog to send logs to a remote log server, open <code>/etc/rsyslog.conf</code> and read and understand the last section of the file,...
    Rule Medium Severity
    Show

  • Network Configuration and Firewalls

    Most systems must be connected to a network of some sort, and this brings with it the substantial risk of network attack. This section discusses th...
    Group
    Show

  • Configure Multiple DNS Servers in /etc/resolv.conf

    Determine whether the system is using local or DNS name resolution with the following command: <pre>$ sudo grep hosts /etc/nsswitch.conf hosts: fi...
    Rule Medium Severity
    Show

  • Ensure System is Not Acting as a Network Sniffer

    The system should not be acting as a network sniffer, which can capture all traffic on the network to which it is connected. Run the following to d...
    Rule Medium Severity
    Show

  • firewalld

    The dynamic firewall daemon <code>firewalld</code> provides a dynamically managed firewall with support for network “zones” to assign a level of tr...
    Group
    Show

  • Configure Firewalld to Use the Nftables Backend

    Firewalld can be configured with many backends, such as nftables.
    Rule Medium Severity
    Show

  • Inspect and Activate Default firewalld Rules

    Firewalls can be used to separate networks into different zones based on the level of trust the user has decided to place on the devices and traffi...
    Group
    Show

  • Install firewalld Package

    The firewalld package can be installed with the following command: 
    $ sudo dnf install firewalld
    Rule Medium Severity
    Show

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in configuration files under t...
    Group
    Show

  • Configure the Firewalld Ports

    Configure the <code>firewalld</code> ports to allow approved services to have access to the system. To configure <code>firewalld</code> to open por...
    Rule Medium Severity
    Show

  • Firewalld Must Employ a Deny-all, Allow-by-exception Policy for Allowing Connections to Other Systems

    Red Hat Enterprise Linux 9 incorporates the "firewalld" daemon, which allows for many different configurations. One of these configurations is zone...
    Rule Medium Severity
    Show

  • IPSec Support

    Support for Internet Protocol Security (IPsec) is provided with Libreswan.
    Group
    Show

  • Install libreswan Package

    The libreswan package provides an implementation of IPsec and IKE, which permits the creation of secure tunnels over untrusted networks. The <code>...
    Rule Medium Severity
    Show

  • Verify Any Configured IPSec Tunnel Connections

    Libreswan provides an implementation of IPsec and IKE, which permits the creation of secure tunnels over untrusted networks. As such, IPsec can be ...
    Rule Medium Severity
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the numb...
    Group
    Show

  • Configure IPv6 Settings if Necessary

    A major feature of IPv6 is the extent to which systems implementing it can automatically configure their networking devices using information from ...
    Group
    Show

  • Configure Accepting Router Advertisements on All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ip...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules