Skip to content
ATO Pathways
  Log In

PCI-DSS v4.0 Control Baseline for Red Hat Enterprise Linux 9

Rules and Groups employed by this XCCDF Profile

  • Telnet

    The telnet protocol does not provide confidentiality or integrity for information transmitted on the network. This includes authentication informat...
    Group
    Show

  • Uninstall telnet-server Package

    The telnet-server package can be removed with the following command: 
    $ sudo dnf erase telnet-server
    Rule High Severity
    Show

  • Remove telnet Clients

    The telnet client allows users to start connections to other systems via the telnet protocol.
    Rule Low Severity
    Show

  • TFTP Server

    TFTP is a lightweight version of the FTP protocol which has traditionally been used to configure networking equipment. However, TFTP provides littl...
    Group
    Show

  • Uninstall tftp-server Package

    The tftp-server package can be removed with the following command: 
     $ sudo dnf erase tftp-server
    Rule High Severity
    Show

  • Remove tftp Daemon

    Trivial File Transfer Protocol (TFTP) is a simple file transfer protocol, typically used to automatically transfer configuration or boot files betw...
    Rule Low Severity
    Show

  • SNMP Server

    The Simple Network Management Protocol allows administrators to monitor the state of network devices, including computers. Older versions of SNMP w...
    Group
    Show

  • Disable SNMP Server if Possible

    The system includes an SNMP daemon that allows for its remote monitoring, though it not installed by default. If it was installed and activated but...
    Group
    Show

  • Uninstall net-snmp Package

    The <code>net-snmp</code> package provides the snmpd service. The <code>net-snmp</code> package can be removed with the following command: <pre> $...
    Rule Unknown Severity
    Show

  • SSH Server

    The SSH protocol is recommended for remote login and remote file transfer. SSH provides confidentiality and integrity for data exchanged between tw...
    Group
    Show

  • Verify Permissions on SSH Server config file

    To properly set the permissions of /etc/ssh/sshd_config, run the command: 
    $ sudo chmod 0600 /etc/ssh/sshd_config
    Rule Medium Severity
    Show

  • Verify Permissions on SSH Server Private *_key Key Files

    SSH server private keys - files that match the <code>/etc/ssh/*_key</code> glob, have to have restricted permissions. If those files are owned by t...
    Rule Medium Severity
    Show

  • Verify Permissions on SSH Server Public *.pub Key Files

    To properly set the permissions of /etc/ssh/*.pub, run the command: 
    $ sudo chmod 0644 /etc/ssh/*.pub
    Rule Medium Severity
    Show

  • Configure OpenSSH Server if Necessary

    If the system needs to act as an SSH server, then certain changes should be made to the OpenSSH daemon configuration file <code>/etc/ssh/sshd_confi...
    Group
    Show

  • Set SSH Client Alive Count Max

    The SSH server sends at most <code>ClientAliveCountMax</code> messages during a SSH session and waits for a response from the SSH client. The optio...
    Rule Medium Severity
    Show

  • Set SSH Client Alive Interval

    SSH allows administrators to set a network responsiveness timeout interval. After this interval has passed, the unresponsive client will be automat...
    Rule Medium Severity
    Show

  • Disable Host-Based Authentication

    SSH's cryptographic host-based authentication is more secure than <code>.rhosts</code> authentication. However, it is not recommended that hosts un...
    Rule Medium Severity
    Show

  • Disable SSH Access via Empty Passwords

    Disallow SSH login with empty passwords. The default SSH configuration disables logins with empty passwords. The appropriate configuration is used ...
    Rule High Severity
    Show

  • Disable SSH Support for .rhosts Files

    SSH can emulate the behavior of the obsolete rsh command in allowing users to enable insecure access to their accounts via <code>.rhosts</code> fil...
    Rule Medium Severity
    Show

  • Disable SSH Root Login

    The root user should never be allowed to login to a system directly over a network. To disable root login via SSH, add or correct the following lin...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules