Skip to content
ATO Pathways
  Log In

DRAFT - Unclassified Information in Non-federal Information Systems and Organizations (NIST 800-171)

Rules and Groups employed by this XCCDF Profile

  • Configure SELinux Policy

    The SELinux <code>targeted</code> policy is appropriate for general-purpose desktops and servers, as well as systems in many other roles. To config...
    Rule Medium Severity
    Show

  • Ensure SELinux State is Enforcing

    The SELinux state should be set to <code><xccdf-1.2:sub idref="xccdf_org.ssgproject.content_value_var_selinux_state" use="legacy"></xccdf-1.2:sub><...
    Rule High Severity
    Show

  • Services

    The best protection against vulnerable software is running less software. This section describes how to review the software which Red Hat Enterpris...
    Group
    Show

  • Base Services

    This section addresses the base services that are installed on a Red Hat Enterprise Linux 9 default installation which are not covered in other sec...
    Group
    Show

  • Disable KDump Kernel Crash Analyzer (kdump)

    The <code>kdump</code> service provides a kernel crash dump analyzer. It uses the <code>kexec</code> system call to boot a secondary kernel ("captu...
    Rule Medium Severity
    Show

  • Application Whitelisting Daemon

    Fapolicyd (File Access Policy Daemon) implements application whitelisting to decide file access rights. Applications that are known via a reputatio...
    Group
    Show

  • Install fapolicyd Package

    The fapolicyd package can be installed with the following command: 
    $ sudo dnf install fapolicyd
    Rule Medium Severity
    Show

  • Enable the File Access Policy Service

    The File Access Policy service should be enabled. The <code>fapolicyd</code> service can be enabled with the following command: <pre>$ sudo system...
    Rule Medium Severity
    Show

  • Network Time Protocol

    The Network Time Protocol is used to manage the system clock over a network. Computer clocks are not very accurate, so time will drift unpredictabl...
    Group
    Show

  • The Chrony package is installed

    System time should be synchronized between all systems in an environment. This is typically done by establishing an authoritative time server or se...
    Rule Medium Severity
    Show

  • Disable chrony daemon from acting as server

    The <code>port</code> option in <code>/etc/chrony.conf</code> can be set to <code>0</code> to make chrony daemon to never open any listening port f...
    Rule Low Severity
    Show

  • SSH Server

    The SSH protocol is recommended for remote login and remote file transfer. SSH provides confidentiality and integrity for data exchanged between tw...
    Group
    Show

  • Install OpenSSH client software

    The openssh-clients package can be installed with the following command: 
    $ sudo dnf install openssh-clients
    Rule Medium Severity
    Show

  • Install the OpenSSH Server Package

    The <code>openssh-server</code> package should be installed. The <code>openssh-server</code> package can be installed with the following command: <...
    Rule Medium Severity
    Show

  • Configure OpenSSH Client if Necessary

    The following configuration changes apply to the SSH client. They can improve security parameters relwevant to the client user, e.g. increasing ent...
    Group
    Show

  • Configure session renegotiation for SSH client

    The <code>RekeyLimit</code> parameter specifies how often the session key is renegotiated, both in terms of amount of data that may be transmitted ...
    Rule Medium Severity
    Show

  • Configure OpenSSH Server if Necessary

    If the system needs to act as an SSH server, then certain changes should be made to the OpenSSH daemon configuration file <code>/etc/ssh/sshd_confi...
    Group
    Show

  • Disable Host-Based Authentication

    SSH's cryptographic host-based authentication is more secure than <code>.rhosts</code> authentication. However, it is not recommended that hosts un...
    Rule Medium Severity
    Show

  • Disable SSH Access via Empty Passwords

    Disallow SSH login with empty passwords. The default SSH configuration disables logins with empty passwords. The appropriate configuration is used ...
    Rule High Severity
    Show

  • Disable GSSAPI Authentication

    Unless needed, SSH should not permit extraneous or unnecessary authentication mechanisms like GSSAPI. <br> The default SSH configuration disallows ...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules