Skip to content
ATO Pathways
  Log In

CIS Red Hat Enterprise Linux 8 Benchmark for Level 2 - Server

Rules and Groups employed by this XCCDF Profile

  • Disable systemd-journal-remote Socket

    Journald supports the ability to receive messages from remote hosts, thus acting as a log server. Clients should not receive data from other hosts....
    Rule Medium Severity
    Show

  • Configure rsyslogd to Accept Remote Messages If Acting as a Log Server

    By default, <code>rsyslog</code> does not listen over the network for log messages. If needed, modules can be enabled to allow the rsyslog daemon t...
    Group
    Show

  • Ensure rsyslog Does Not Accept Remote Messages Unless Acting As Log Server

    The <code>rsyslog</code> daemon should not accept remote messages unless the system acts as a log server. To ensure that it is not listening on the...
    Rule Medium Severity
    Show

  • Network Configuration and Firewalls

    Most systems must be connected to a network of some sort, and this brings with it the substantial risk of network attack. This section discusses th...
    Group
    Show

  • firewalld

    The dynamic firewall daemon <code>firewalld</code> provides a dynamically managed firewall with support for network “zones” to assign a level of tr...
    Group
    Show

  • Inspect and Activate Default firewalld Rules

    Firewalls can be used to separate networks into different zones based on the level of trust the user has decided to place on the devices and traffi...
    Group
    Show

  • Install firewalld Package

    The firewalld package can be installed with the following command: 
    $ sudo yum install firewalld
    Rule Medium Severity
    Show

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in configuration files under t...
    Group
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the numb...
    Group
    Show

  • Configure IPv6 Settings if Necessary

    A major feature of IPv6 is the extent to which systems implementing it can automatically configure their networking devices using information from ...
    Group
    Show

  • Configure Accepting Router Advertisements on All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ip...
    Rule Medium Severity
    Show

  • Disable Accepting ICMP Redirects for All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on all IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for IPv6 Forwarding

    To set the runtime status of the <code>net.ipv6.conf.all.forwarding</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.i...
    Rule Medium Severity
    Show

  • Disable Accepting Router Advertisements on all IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w ne...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysct...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sy...
    Rule Medium Severity
    Show

  • Kernel Parameters Which Affect Networking

    The <code>sysctl</code> utility is used to set parameters which affect the operation of the Linux kernel. Kernel parameters which affect networking...
    Group
    Show

  • Network Related Kernel Runtime Parameters for Hosts and Routers

    Certain kernel parameters should be set for systems which are acting as either hosts or routers to improve the system's ability defend against cert...
    Group
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules