Skip to content
Log In

DISA STIG for Oracle Linux 8

Rules and Groups employed by this XCCDF Profile

  • Install firewalld Package

    The firewalld package can be installed with the following command: 
    $ sudo yum install firewalld
    Rule Medium Severity
    Show

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in configuration files under the <code>/etc/firewalld/services</code> and <code>...
    Group
    Show

  • Configure the Firewalld Ports

    Configure the <code>firewalld</code> ports to allow approved services to have access to the system. To configure <code>firewalld</code> to open ports, run the following command: <pre>firewall-cmd -...
    Rule Medium Severity
    Show

  • Firewalld Must Employ a Deny-all, Allow-by-exception Policy for Allowing Connections to Other Systems

    Oracle Linux 8 incorporates the "firewalld" daemon, which allows for many different configurations. One of these configurations is zones. Zones can be utilized to a deny-all, allow-by-exception app...
    Rule Medium Severity
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the number of available addresses. Another important featu...
    Group
    Show

  • Configure IPv6 Settings if Necessary

    A major feature of IPv6 is the extent to which systems implementing it can automatically configure their networking devices using information from the network. From a security perspective, manually...
    Group
    Show

  • Configure Accepting Router Advertisements on All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.all.accept_ra=0</pre> To make sure that th...
    Rule Medium Severity
    Show

  • Disable Accepting ICMP Redirects for All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.all.accept_redirects=0</pre> To mak...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on all IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.all.accept_source_route=0</pre> ...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for IPv6 Forwarding

    To set the runtime status of the <code>net.ipv6.conf.all.forwarding</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.all.forwarding=0</pre> To make sure that ...
    Rule Medium Severity
    Show

  • Disable Accepting Router Advertisements on all IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.default.accept_ra=0</pre> To make sure...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.default.accept_redirects=0</pre...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.default.accept_source_route=...
    Rule Medium Severity
    Show

  • Kernel Parameters Which Affect Networking

    The sysctl utility is used to set parameters which affect the operation of the Linux kernel. Kernel parameters which affect networking and have security implications are described here.
    Group
    Show

  • Network Related Kernel Runtime Parameters for Hosts and Routers

    Certain kernel parameters should be set for systems which are acting as either hosts or routers to improve the system's ability defend against certain types of IPv4 protocol attacks.
    Group
    Show

  • Disable Accepting ICMP Redirects for All IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.accept_redirects=0</pre> To mak...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.accept_source_route=0</pre> ...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Use Reverse Path Filtering on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.rp_filter</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.rp_filter=1</pre> To make sure that th...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.accept_redirects=0</pre...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.accept_source_route=...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Ignore ICMP Broadcast Echo Requests on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.icmp_echo_ignore_broadcasts</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.icmp_echo_ignore_broadcasts=1</pre> To...
    Rule Medium Severity
    Show

  • Network Parameters for Hosts Only

    If the system is not going to be used as a router, then setting certain kernel parameters ensure that the host will not perform routing of network traffic.
    Group
    Show

  • Disable Kernel Parameter for Sending ICMP Redirects on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.send_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.send_redirects=0</pre> To make su...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Sending ICMP Redirects on all IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.send_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.send_redirects=0</pre> To...
    Rule Medium Severity
    Show

  • Uncommon Network Protocols

    The system includes support for several network protocols which are not commonly used. Although security vulnerabilities in kernel networking code are not frequently discovered, the consequences ca...
    Group
    Show

  • Disable ATM Support

    The Asynchronous Transfer Mode (ATM) is a protocol operating on network, data link, and physical layers, based on virtual circuits and virtual paths. To configure the system to prevent the <code>a...
    Rule Medium Severity
    Show

  • Disable CAN Support

    The Controller Area Network (CAN) is a serial communications protocol which was initially developed for automotive and is now also used in marine, industrial, and medical applications. To configur...
    Rule Medium Severity
    Show

  • Disable IEEE 1394 (FireWire) Support

    The IEEE 1394 (FireWire) is a serial bus standard for high-speed real-time communication. To configure the system to prevent the <code>firewire-core</code> kernel module from being loaded, add the...
    Rule Low Severity
    Show

  • Disable SCTP Support

    The Stream Control Transmission Protocol (SCTP) is a transport layer protocol, designed to support the idea of message-oriented communication, with several streams of messages within one connection...
    Rule Medium Severity
    Show

  • Disable TIPC Support

    The Transparent Inter-Process Communication (TIPC) protocol is designed to provide communications between nodes in a cluster. To configure the system to prevent the <code>tipc</code> kernel module...
    Rule Low Severity
    Show

  • Wireless Networking

    Wireless networking, such as 802.11 (WiFi) and Bluetooth, can present a security risk to sensitive or classified systems and networks. Wireless networking hardware is much more likely to be include...
    Group
    Show

  • Disable Wireless Through Software Configuration

    If it is impossible to remove the wireless hardware from the device in question, disable as much of it as possible through software. The following methods can disable software support for wireless ...
    Group
    Show

  • Disable Bluetooth Kernel Module

    The kernel's module loading system can be configured to prevent loading of the Bluetooth module. Add the following to the appropriate <code>/etc/modprobe.d</code> configuration file to prevent the ...
    Rule Medium Severity
    Show

  • Deactivate Wireless Network Interfaces

    Deactivating wireless network interfaces should prevent normal usage of the wireless capability. <br> <br> Configure the system to disable all wireless network interfaces with the followi...
    Rule Medium Severity
    Show

  • File Permissions and Masks

    Traditional Unix security relies heavily on file and directory permissions to prevent unauthorized users from reading or modifying files to which they should not have access. <br> <br> Severa...
    Group
    Show

  • Verify Permissions on Important Files and Directories

    Permissions for many files on a system must be set restrictively to ensure sensitive information is properly protected. This section discusses important permission restrictions which can be verifie...
    Group
    Show

  • Verify that All World-Writable Directories Have Sticky Bits Set

    When the so-called 'sticky bit' is set on a directory, only the owner of a given file may remove that file from the directory. Without the sticky bit, any user with write access to a directory may ...
    Rule Medium Severity
    Show

  • Ensure All World-Writable Directories Are Owned by a System Account

    All directories in local partitions which are world-writable should be owned by root or another system account. If any world-writable directories are not owned by a system account, this should be i...
    Rule Medium Severity
    Show

  • Ensure All World-Writable Directories Are Group Owned by a System Account

    All directories in local partitions which are world-writable should be group owned by root or another system account. If any world-writable directories are not group owned by a system account, this...
    Rule Medium Severity
    Show

  • Verify Permissions on /etc/audit/auditd.conf

    To properly set the permissions of /etc/audit/auditd.conf, run the command: 
    $ sudo chmod 0640 /etc/audit/auditd.conf
    Rule Medium Severity
    Show

  • Verify Permissions on /etc/audit/rules.d/*.rules

    To properly set the permissions of /etc/audit/rules.d/*.rules, run the command: 
    $ sudo chmod 0640 /etc/audit/rules.d/*.rules
    Rule Medium Severity
    Show

  • Ensure All Files Are Owned by a Group

    If any file is not group-owned by a group present in /etc/group, the cause of the lack of group-ownership must be investigated. Following this, those files should be deleted or assigned to an appro...
    Rule Medium Severity
    Show

  • Ensure All Files Are Owned by a User

    If any files are not owned by a user, then the cause of their lack of ownership should be investigated. Following this, the files should be deleted or assigned to an appropriate user. Locate the m...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Enforce DAC on Hardlinks

    To set the runtime status of the <code>fs.protected_hardlinks</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w fs.protected_hardlinks=1</pre> To make sure that the setting ...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Enforce DAC on Symlinks

    To set the runtime status of the <code>fs.protected_symlinks</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w fs.protected_symlinks=1</pre> To make sure that the setting is...
    Rule Medium Severity
    Show

  • Verify Permissions on Files within /var/log Directory

    The /var/log directory contains files with logs of error messages in the system and should only be accessed by authorized personnel.
    Group
    Show

  • Verify Group Who Owns /var/log Directory

    To properly set the group owner of /var/log, run the command: 
    $ sudo chgrp root /var/log
    Rule Medium Severity
    Show

  • Verify Group Who Owns /var/log/messages File

    To properly set the group owner of /var/log/messages, run the command: 
    $ sudo chgrp root /var/log/messages
    Rule Medium Severity
    Show

  • Verify User Who Owns /var/log Directory

    To properly set the owner of /var/log, run the command: 
    $ sudo chown root /var/log
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules