Skip to content
Log In

DISA STIG with GUI for Oracle Linux 7

Rules and Groups employed by this XCCDF Profile

  • Install firewalld Package

    The firewalld package can be installed with the following command: 
    $ sudo yum install firewalld
    Rule Medium Severity
    Show

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in configuration files under the <code>/etc/firewalld/services</code> and <code>...
    Group
    Show

  • Configure the Firewalld Ports

    Configure the <code>firewalld</code> ports to allow approved services to have access to the system. To configure <code>firewalld</code> to open ports, run the following command: <pre>firewall-cmd -...
    Rule Medium Severity
    Show

  • IPSec Support

    Support for Internet Protocol Security (IPsec) is provided with Libreswan.
    Group
    Show

  • Verify Any Configured IPSec Tunnel Connections

    Libreswan provides an implementation of IPsec and IKE, which permits the creation of secure tunnels over untrusted networks. As such, IPsec can be used to circumvent certain network requirements su...
    Rule Medium Severity
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the number of available addresses. Another important featu...
    Group
    Show

  • Configure IPv6 Settings if Necessary

    A major feature of IPv6 is the extent to which systems implementing it can automatically configure their networking devices using information from the network. From a security perspective, manually...
    Group
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on all IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv6.conf.all.accept_source_route=0</pre> ...
    Rule Medium Severity
    Show

  • Kernel Parameters Which Affect Networking

    The sysctl utility is used to set parameters which affect the operation of the Linux kernel. Kernel parameters which affect networking and have security implications are described here.
    Group
    Show

  • Network Related Kernel Runtime Parameters for Hosts and Routers

    Certain kernel parameters should be set for systems which are acting as either hosts or routers to improve the system's ability defend against certain types of IPv4 protocol attacks.
    Group
    Show

  • Disable Accepting ICMP Redirects for All IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.accept_redirects=0</pre> To mak...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.accept_source_route=0</pre> ...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Use Reverse Path Filtering on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.rp_filter</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.rp_filter=1</pre> To make sure that th...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.accept_redirects=0</pre...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.accept_source_route=...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Use Reverse Path Filtering on all IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.rp_filter</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.rp_filter=1</pre> To make sure...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Ignore ICMP Broadcast Echo Requests on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.icmp_echo_ignore_broadcasts</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.icmp_echo_ignore_broadcasts=1</pre> To...
    Rule Medium Severity
    Show

  • Configure Kernel to Rate Limit Sending of Duplicate TCP Acknowledgments

    Make sure that the system is configured to limit the maximal rate for sending duplicate acknowledgments in response to incoming TCP packets that are for an existing connection but that are invalid ...
    Rule Medium Severity
    Show

  • Network Parameters for Hosts Only

    If the system is not going to be used as a router, then setting certain kernel parameters ensure that the host will not perform routing of network traffic.
    Group
    Show

  • Disable Kernel Parameter for Sending ICMP Redirects on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.send_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.send_redirects=0</pre> To make su...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Sending ICMP Redirects on all IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.send_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.send_redirects=0</pre> To...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for IP Forwarding on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.ip_forward</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.ip_forward=0</pre> To make sure that the setting is per...
    Rule Medium Severity
    Show

  • Uncommon Network Protocols

    The system includes support for several network protocols which are not commonly used. Although security vulnerabilities in kernel networking code are not frequently discovered, the consequences ca...
    Group
    Show

  • Disable DCCP Support

    The Datagram Congestion Control Protocol (DCCP) is a relatively new transport layer protocol, designed to support streaming media and telephony. To configure the system to prevent the <code>dccp</...
    Rule Medium Severity
    Show

  • Wireless Networking

    Wireless networking, such as 802.11 (WiFi) and Bluetooth, can present a security risk to sensitive or classified systems and networks. Wireless networking hardware is much more likely to be include...
    Group
    Show

  • Disable Wireless Through Software Configuration

    If it is impossible to remove the wireless hardware from the device in question, disable as much of it as possible through software. The following methods can disable software support for wireless ...
    Group
    Show

  • Deactivate Wireless Network Interfaces

    Deactivating wireless network interfaces should prevent normal usage of the wireless capability. <br> <br> Configure the system to disable all wireless network interfaces with the followi...
    Rule Medium Severity
    Show

  • File Permissions and Masks

    Traditional Unix security relies heavily on file and directory permissions to prevent unauthorized users from reading or modifying files to which they should not have access. <br> <br> Severa...
    Group
    Show

  • Verify Permissions on Important Files and Directories

    Permissions for many files on a system must be set restrictively to ensure sensitive information is properly protected. This section discusses important permission restrictions which can be verifie...
    Group
    Show

  • Ensure All World-Writable Directories Are Owned by a System Account

    All directories in local partitions which are world-writable should be owned by root or another system account. If any world-writable directories are not owned by a system account, this should be i...
    Rule Medium Severity
    Show

  • Ensure All World-Writable Directories Are Group Owned by a System Account

    All directories in local partitions which are world-writable should be group owned by root or another system account. If any world-writable directories are not group owned by a system account, this...
    Rule Medium Severity
    Show

  • Ensure All Files Are Owned by a Group

    If any file is not group-owned by a group present in /etc/group, the cause of the lack of group-ownership must be investigated. Following this, those files should be deleted or assigned to an appro...
    Rule Medium Severity
    Show

  • Ensure All Files Are Owned by a User

    If any files are not owned by a user, then the cause of their lack of ownership should be investigated. Following this, the files should be deleted or assigned to an appropriate user. Locate the m...
    Rule Medium Severity
    Show

  • Restrict Dynamic Mounting and Unmounting of Filesystems

    Linux includes a number of facilities for the automated addition and removal of filesystems on a running system. These facilities may be necessary in many environments, but this capability also ca...
    Group
    Show

  • Disable the Automounter

    The <code>autofs</code> daemon mounts and unmounts filesystems, such as user home directories shared via NFS, on demand. In addition, autofs can be used to handle removable media, and the default c...
    Rule Medium Severity
    Show

  • Disable Modprobe Loading of USB Storage Driver

    To prevent USB storage devices from being used, configure the kernel module loading system to prevent automatic loading of the USB storage driver. To configure the system to prevent the <code>usb-...
    Rule Medium Severity
    Show

  • Restrict Partition Mount Options

    System partitions can be mounted with certain options that limit what files on those partitions can do. These options are set in the <code>/etc/fstab</code> configuration file, and can be used to m...
    Group
    Show

  • Add nodev Option to /dev/shm

    The <code>nodev</code> mount option can be used to prevent creation of device files in <code>/dev/shm</code>. Legitimate character and block devices should not exist within temporary directories li...
    Rule Medium Severity
    Show

  • Add noexec Option to /dev/shm

    The <code>noexec</code> mount option can be used to prevent binaries from being executed out of <code>/dev/shm</code>. It can be dangerous to allow the execution of binaries from world-writable tem...
    Rule Medium Severity
    Show

  • Add nosuid Option to /dev/shm

    The <code>nosuid</code> mount option can be used to prevent execution of setuid programs in <code>/dev/shm</code>. The SUID and SGID permissions should not be required in these world-writable dire...
    Rule Medium Severity
    Show

  • Add nosuid Option to /home

    The <code>nosuid</code> mount option can be used to prevent execution of setuid programs in <code>/home</code>. The SUID and SGID permissions should not be required in these user data directories. ...
    Rule Medium Severity
    Show

  • Add nosuid Option to Removable Media Partitions

    The <code>nosuid</code> mount option prevents set-user-identifier (SUID) and set-group-identifier (SGID) permissions from taking effect. These permissions allow users to execute binaries with the s...
    Rule Medium Severity
    Show

  • Restrict Programs from Dangerous Execution Patterns

    The recommendations in this section are designed to ensure that the system's features to protect against potentially dangerous program execution are activated. These protections are applied at the ...
    Group
    Show

  • Restrict Access to Kernel Message Buffer

    To set the runtime status of the <code>kernel.dmesg_restrict</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w kernel.dmesg_restrict=1</pre> To make sure that the setting is...
    Rule Low Severity
    Show

  • Enable ExecShield

    ExecShield describes kernel features that provide protection against exploitation of memory corruption errors such as buffer overflows. These features include random placement of the stack and othe...
    Group
    Show

  • Enable Randomized Layout of Virtual Address Space

    To set the runtime status of the <code>kernel.randomize_va_space</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w kernel.randomize_va_space=2</pre> To make sure that the se...
    Rule Medium Severity
    Show

  • SELinux

    SELinux is a feature of the Linux kernel which can be used to guard against misconfigured or compromised programs. SELinux enforces the idea that programs should be limited in what files they can a...
    Group
    Show

  • Ensure No Device Files are Unlabeled by SELinux

    Device files, which are used for communication with important system resources, should be labeled with proper SELinux types. If any device files carry the SELinux type <code>device_t</code> or <cod...
    Rule Medium Severity
    Show

  • Confine SELinux Users To Roles That Conform To Least Privilege

    Configure the operating system to confine SELinux users to roles that conform to least privilege. Use the following command to map the "staff_u" SELinux user to the "staff_r" and "sysadm_r" roles: ...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules