Skip to content
ATO Pathways
  Log In

DISA STIG with GUI for Oracle Linux 7

Rules and Groups employed by this XCCDF Profile

  • Set the UEFI Boot Loader Admin Username to a Non-Default Value

    The grub2 boot loader should have a superuser account and password protection enabled to protect boot-time settings. <br><br> To maximize the prote...
    Rule Medium Severity
    Show

  • Set the UEFI Boot Loader Password

    The grub2 boot loader should have a superuser account and password protection enabled to protect boot-time settings. <br><br> Since plaintext passw...
    Rule High Severity
    Show

  • UEFI Boot Loader Is Not Installed On Removeable Media

    The system must not allow removable media to be used as the boot loader. Remove alternate methods of booting the system from removable media. <code...
    Rule Medium Severity
    Show

  • Configure Syslog

    The syslog service has been the default Unix logging mechanism for many years. It has a number of downsides, including inconsistent log format, lac...
    Group
    Show

  • Ensure Proper Configuration of Log Files

    The file <code>/etc/rsyslog.conf</code> controls where log message are written. These are controlled by lines called <i>rules</i>, which consist of...
    Group
    Show

  • Ensure cron Is Logging To Rsyslog

    Cron logging must be implemented to spot intrusions or trace cron job status. If <code>cron</code> is not logging to <code>rsyslog</code>, it can b...
    Rule Medium Severity
    Show

  • Configure rsyslogd to Accept Remote Messages If Acting as a Log Server

    By default, <code>rsyslog</code> does not listen over the network for log messages. If needed, modules can be enabled to allow the rsyslog daemon t...
    Group
    Show

  • Ensure rsyslog Does Not Accept Remote Messages Unless Acting As Log Server

    The <code>rsyslog</code> daemon should not accept remote messages unless the system acts as a log server. To ensure that it is not listening on the...
    Rule Medium Severity
    Show

  • Rsyslog Logs Sent To Remote Host

    If system logs are to be useful in detecting malicious activities, it is necessary to send logs to a remote server. An intruder who has compromised...
    Group
    Show

  • Ensure Logs Sent To Remote Host

    To configure rsyslog to send logs to a remote log server, open <code>/etc/rsyslog.conf</code> and read and understand the last section of the file,...
    Rule Medium Severity
    Show

  • Network Configuration and Firewalls

    Most systems must be connected to a network of some sort, and this brings with it the substantial risk of network attack. This section discusses th...
    Group
    Show

  • Configure Multiple DNS Servers in /etc/resolv.conf

    Determine whether the system is using local or DNS name resolution with the following command: <pre>$ sudo grep hosts /etc/nsswitch.conf hosts: fi...
    Rule Medium Severity
    Show

  • Grant Or Deny System Access To Specific Hosts And Services

    To verify the system's access control program is configured to grant or deny system access to specific hosts check to see if "firewalld" is active ...
    Rule Medium Severity
    Show

  • Ensure System is Not Acting as a Network Sniffer

    The system should not be acting as a network sniffer, which can capture all traffic on the network to which it is connected. Run the following to d...
    Rule Medium Severity
    Show

  • firewalld

    The dynamic firewall daemon <code>firewalld</code> provides a dynamically managed firewall with support for network “zones” to assign a level of tr...
    Group
    Show

  • Inspect and Activate Default firewalld Rules

    Firewalls can be used to separate networks into different zones based on the level of trust the user has decided to place on the devices and traffi...
    Group
    Show

  • Install firewalld Package

    The firewalld package can be installed with the following command: 
    $ sudo yum install firewalld
    Rule Medium Severity
    Show

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in configuration files under t...
    Group
    Show

  • Configure the Firewalld Ports

    Configure the <code>firewalld</code> ports to allow approved services to have access to the system. To configure <code>firewalld</code> to open por...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules