II - Mission Support Classified
Rules and Groups employed by this XCCDF Profile
-
SRG-NET-000512-RTR-000001
Group -
The Arista BGP router must be configured to use its loopback address as the source address for iBGP peering sessions.
Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of the BGP routers. It is easier to construct appropriate ingress filters...Rule Low Severity -
SRG-NET-000512-RTR-000002
Group -
The MPLS router must be configured to use its loopback address as the source address for LDP peering sessions.
Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of backbone routers. It is easier to construct appropriate ingress filter...Rule Low Severity -
SRG-NET-000512-RTR-000003
Group -
The MPLS router must be configured to synchronize IGP and LDP to minimize packet loss when an IGP adjacency is established prior to LDP peers completing label exchange.
Packet loss can occur when an IGP adjacency is established and the router begins forwarding packets using the new adjacency before the LDP label exchange completes between the peers on that link. P...Rule Low Severity -
SRG-NET-000512-RTR-000004
Group -
The MPLS router must be configured to have TTL propagation disabled.
The head end of the label-routered path (LSP), the label edge router (LER) will decrement the IP packet's time-to-live (TTL) value by one and then copy the value to the MPLS TTL field. At each labe...Rule Medium Severity -
SRG-NET-000512-RTR-000005
Group -
The PE router must be configured to have each Virtual Routing and Forwarding (VRF) instance bound to the appropriate physical or logical interfaces to maintain traffic separation between all MPLS L3VPNs.
The primary security model for an MPLS L3VPN infrastructure is traffic separation. The service provider must guarantee the customer that traffic from one VPN does not leak into another VPN or into ...Rule High Severity -
SRG-NET-000512-RTR-000006
Group -
The PE router must be configured to have each Virtual Routing and Forwarding (VRF) instance with the appropriate Route Target (RT).
The primary security model for an MPLS L3VPN as well as a VRF-lite infrastructure is traffic separation. Each interface can only be associated to one VRF, which is the fundamental framework for tra...Rule High Severity -
SRG-NET-000512-RTR-000007
Group -
The PE router must be configured to have each VRF with the appropriate Route Distinguisher (RD).
An RD provides uniqueness to the customer address spaces within the MPLS L3VPN infrastructure. The concept of the VPN-IPv4 and VPN-IPv6 address families consists of the RD prepended before the IP a...Rule Medium Severity -
SRG-NET-000512-RTR-000008
Group -
The PE router providing MPLS Virtual Private Wire Service (VPWS) must be configured to have the appropriate virtual circuit identification (VC ID) for each attachment circuit.
VPWS is an L2VPN technology that provides a virtual circuit between two PE routers to forward Layer 2 frames between two customer-edge routers or routers through an MPLS-enabled IP core. The ingres...Rule High Severity -
SRG-NET-000512-RTR-000011
Group -
The Arista Multicast Source Discovery Protocol (MSDP) router must be configured to use its loopback address as the source address when originating MSDP traffic.
Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of MSDP routers. It is easier to construct appropriate ingress filters fo...Rule Low Severity -
SRG-NET-000512-RTR-000012
Group -
The Arista router must be configured to advertise a hop limit of at least 32 in Router Advertisement messages for IPv6 stateless auto-configuration deployments.
The Neighbor Discovery protocol allows a hop limit value to be advertised by routers in a Router Advertisement message being used by hosts instead of the standardized default value. If a very small...Rule Low Severity
Node 2
The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.