Skip to content
Log In

Guide to the Secure Configuration of OpenEmbedded

Rules, Groups, and Values defined within the XCCDF Benchmark

  • Disable netfs if Possible

    To determine if any network filesystems handled by netfs are currently mounted on the system execute the following command: <pre>$ mount -t nfs,nfs4,smbfs,cifs,ncpfs</pre> If the command did not re...
    Group
    Show

  • Disable Services Used Only by NFS

    If NFS is not needed, disable the NFS client daemons nfslock, rpcgssd, and rpcidmapd. <br> <br> All of these daemons run with elevated privileges, and many listen for network connections. I...
    Group
    Show

  • Disable rpcbind Service

    The rpcbind utility maps RPC services to the ports on which they listen. RPC processes notify rpcbind when they start, registering the ports they are listening on and the RPC program numbers they e...
    Rule Low Severity
    Show

  • Configure NFS Clients

    The steps in this section are appropriate for systems which operate as NFS clients.
    Group
    Show

  • Disable NFS Server Daemons

    There is no need to run the NFS server daemons <code>nfs</code> and <code>rpcsvcgssd</code> except on a small number of properly secured systems designated as NFS servers. Ensure that these daemons...
    Group
    Show

  • Configure NFS Servers

    The steps in this section are appropriate for systems which operate as NFS servers.
    Group
    Show

  • Ensure All-Squashing Disabled On All Exports

    The <code>all_squash</code> maps all uids and gids to an anonymous user. This should be disabled by removing any instances of the <code>all_squash</code> option from the file <code>/etc/exports</co...
    Rule Low Severity
    Show

  • Network Time Protocol

    The Network Time Protocol is used to manage the system clock over a network. Computer clocks are not very accurate, so time will drift unpredictably on unmanaged systems. Central time protocols can...
    Group
    Show

  • Vendor Approved Time Servers

    The list of vendor-approved time servers
    Value
    Show

  • Disable Samba if Possible

    Even after the Samba server package has been installed, it will remain disabled. Do not enable this service unless it is absolutely necessary to provide Microsoft Windows file and print sharing fun...
    Group
    Show

  • SNMP Server

    The Simple Network Management Protocol allows administrators to monitor the state of network devices, including computers. Older versions of SNMP were well-known for weak security, such as plaintex...
    Group
    Show

  • Disable SNMP Server if Possible

    The system includes an SNMP daemon that allows for its remote monitoring, though it not installed by default. If it was installed and activated but is not needed, the software should be disabled an...
    Group
    Show

  • Disable snmpd Service

    The snmpd service can be disabled with the following command: 
    $ sudo systemctl mask --now snmpd.service
    Rule Low Severity
    Show

  • SSH Server

    The SSH protocol is recommended for remote login and remote file transfer. SSH provides confidentiality and integrity for data exchanged between two systems, as well as server authentication, throu...
    Group
    Show

  • Set SSH Client Alive Count Max

    The SSH server sends at most <code>ClientAliveCountMax</code> messages during a SSH session and waits for a response from the SSH client. The option <code>ClientAliveInterval</code> configures time...
    Rule Medium Severity
    Show

  • Disable Host-Based Authentication

    SSH's cryptographic host-based authentication is more secure than <code>.rhosts</code> authentication. However, it is not recommended that hosts unilaterally trust one another, even within an organ...
    Rule Medium Severity
    Show

  • Allow Only SSH Protocol 2

    Only SSH protocol version 2 connections should be permitted. The default setting in <code>/etc/ssh/sshd_config</code> is correct, and can be verified by ensuring that the following line appears: <p...
    Rule High Severity
    Show

  • Disable SSH Access via Empty Passwords

    Disallow SSH login with empty passwords. The default SSH configuration disables logins with empty passwords. The appropriate configuration is used if no value is set for <code>PermitEmptyPasswords<...
    Rule High Severity
    Show

  • Disable GSSAPI Authentication

    Unless needed, SSH should not permit extraneous or unnecessary authentication mechanisms like GSSAPI. <br> The default SSH configuration disallows authentications based on GSSAPI. The appropriate c...
    Rule Medium Severity
    Show

  • Disable Kerberos Authentication

    Unless needed, SSH should not permit extraneous or unnecessary authentication mechanisms like Kerberos. <br> The default SSH configuration disallows authentication validation through Kerberos. The ...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules