Skip to content
Log In

Guide to the Secure Configuration of OpenEmbedded

Rules, Groups, and Values defined within the XCCDF Benchmark

  • net.ipv4.conf.all.accept_source_route

    Trackers could be using source-routed packets to generate traffic that seems to be intra-net, but actually was created outside and has been redirected.
    Value
    Show

  • net.ipv4.conf.default.arp_filter

    Controls whether the ARP filter is enabled or not. 1 - Allows you to have multiple network interfaces on the same subnet, and have the ARPs for each interface be answered based on whether or not t...
    Value
    Show

  • net.ipv4.conf.default.arp_ignore

    Control the response modes for ARP queries that resolve local target IP addresses: 0 - (default): reply for any local target IP address, configured on any interface 1 - reply only if the target IP...
    Value
    Show

  • net.ipv4.conf.all.log_martians

    Disable so you don't Log Spoofed Packets, Source Routed Packets, Redirect Packets
    Value
    Show

  • net.ipv4.conf.all.rp_filter

    Enable to enforce sanity checking, also called ingress filtering or egress filtering. The point is to drop a packet if the source and destination IP addresses in the IP header do not make sense whe...
    Value
    Show

  • net.ipv4.conf.all.secure_redirects

    Enable to prevent hijacking of routing path by only allowing redirects from gateways known in routing table. Disable to refuse acceptance of secure ICMP redirected packets on all interfaces.
    Value
    Show

  • net.ipv4.conf.all.shared_media

    Controls whether the system can send (router) or accept (host) RFC1620 shared media redirects. <code>shared_media</code> for the interface will be enabled if at least one of conf/{all,interface}/sh...
    Value
    Show

  • net.ipv4.conf.default.accept_redirects

    Disable ICMP Redirect Acceptance?
    Value
    Show

  • net.ipv4.conf.default.accept_source_route

    Disable IP source routing?
    Value
    Show

  • net.ipv4.conf.default.log_martians

    Disable so you don't Log Spoofed Packets, Source Routed Packets, Redirect Packets
    Value
    Show

  • Configure Response Mode of ARP Requests for All IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.arp_ignore</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.arp_ignore=<xccdf-1.2:sub idref="xccd...
    Rule Medium Severity
    Show

  • Prevent Routing External Traffic to Local Loopback on All IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.route_localnet</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.route_localnet=0</pre> To make su...
    Rule Medium Severity
    Show

  • Configure Sending and Accepting Shared Media Redirects by Default

    To set the runtime status of the <code>net.ipv4.conf.default.shared_media</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.shared_media=<xccdf-1.2:sub...
    Rule Medium Severity
    Show

  • Network Parameters for Hosts Only

    If the system is not going to be used as a router, then setting certain kernel parameters ensure that the host will not perform routing of network traffic.
    Group
    Show

  • Uncomplicated Firewall (ufw)

    The Linux kernel in Ubuntu provides a packet filtering system called netfilter, and the traditional interface for manipulating netfilter are the iptables suite of commands. iptables provide a compl...
    Group
    Show

  • Uncommon Network Protocols

    The system includes support for several network protocols which are not commonly used. Although security vulnerabilities in kernel networking code are not frequently discovered, the consequences ca...
    Group
    Show

  • Disable TIPC Support

    The Transparent Inter-Process Communication (TIPC) protocol is designed to provide communications between nodes in a cluster. To configure the system to prevent the <code>tipc</code> kernel module...
    Rule Low Severity
    Show

  • File Permissions and Masks

    Traditional Unix security relies heavily on file and directory permissions to prevent unauthorized users from reading or modifying files to which they should not have access. <br> <br> Severa...
    Group
    Show

  • Verify Permissions on Important Files and Directories

    Permissions for many files on a system must be set restrictively to ensure sensitive information is properly protected. This section discusses important permission restrictions which can be verifie...
    Group
    Show

  • Verify Permissions on System.map Files

    The System.map files are symbol map files generated during the compilation of the Linux kernel. They contain the mapping between kernel symbols and their corresponding memory addresses. In general,...
    Rule Low Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules