Skip to content
ATO Pathways
  Log In

Guide to the Secure Configuration of Ubuntu 20.04

Rules, Groups, and Values defined within the XCCDF Benchmark

  • Restrict ICMP Message Types

    In <code>/etc/sysconfig/iptables</code>, the accepted ICMP messages types can be restricted. To accept only ICMP echo reply, destination unreachabl...
    Group
    Show

  • Log and Drop Packets with Suspicious Source Addresses

    Packets with non-routable source addresses should be rejected, as they may indicate spoofing. Because the modified policy will reject non-matching ...
    Group
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the numb...
    Group
    Show

  • Disable Support for IPv6 Unless Needed

    Despite configuration that suggests support for IPv6 has been disabled, link-local IPv6 address auto-configuration occurs even when only an IPv4 ad...
    Group
    Show

  • Disable IPv6 Networking Support Automatic Loading

    To prevent the IPv6 kernel module (<code>ipv6</code>) from binding to the IPv6 networking stack, add the following line to <code>/etc/modprobe.d/di...
    Rule Medium Severity
    Show

  • net.ipv6.conf.default.accept_source_route

    Trackers could be using source-routed packets to generate traffic that seems to be intra-net, but actually was created outside and has been redirec...
    Value
    Show

  • net.ipv6.conf.default.autoconf

    Enable auto configuration on IPv6 interfaces
    Value
    Show

  • net.ipv6.conf.default.forwarding

    Toggle IPv6 default Forwarding
    Value
    Show

  • net.ipv6.conf.default.max_addresses

    Maximum number of autoconfigured IPv6 addresses
    Value
    Show

  • net.ipv6.conf.default.router_solicitations

    Accept all router solicitations by default?
    Value
    Show

  • Configure Accepting Router Advertisements on All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ip...
    Rule Medium Severity
    Show

  • Disable Accepting ICMP Redirects for All IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on all IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.all.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sysctl...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for IPv6 Forwarding

    To set the runtime status of the <code>net.ipv6.conf.all.forwarding</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.i...
    Rule Medium Severity
    Show

  • Disable Accepting Router Advertisements on all IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_ra</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w ne...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv6 Interfaces

    To set the runtime status of the <code>net.ipv6.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysct...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Source-Routed Packets on IPv6 Interfaces by Default

    To set the runtime status of the <code>net.ipv6.conf.default.accept_source_route</code> kernel parameter, run the following command: <pre>$ sudo sy...
    Rule Medium Severity
    Show

  • net.ipv4.conf.default.secure_redirects

    Enable to prevent hijacking of routing path by only allowing redirects from gateways known in routing table. Disable to refuse acceptance of secure...
    Value
    Show

  • Limit Network-Transmitted Configuration if Using Static IPv6 Addresses

    To limit the configuration information requested from other systems and accepted from the network on a system that uses statically-configured IPv6 ...
    Group
    Show

  • Kernel Parameters Which Affect Networking

    The <code>sysctl</code> utility is used to set parameters which affect the operation of the Linux kernel. Kernel parameters which affect networking...
    Group
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules