Skip to content
ATO Pathways
  Log In

Guide to the Secure Configuration of SUSE Linux Enterprise 12

Rules, Groups, and Values defined within the XCCDF Benchmark

  • iptables and ip6tables

    A host-based firewall called <code>netfilter</code> is included as part of the Linux kernel distributed with the system. It is activated by default...
    Group
    Show

  • Install iptables Package

    The iptables package can be installed with the following command: 
    $ sudo zypper install iptables
    Rule Medium Severity
    Show

  • Inspect and Activate Default Rules

    View the currently-enforced <code>iptables</code> rules by running the command: <pre>$ sudo iptables -nL --line-numbers</pre> The command is analog...
    Group
    Show

  • Verify ip6tables Enabled if Using IPv6

    The ip6tables service can be enabled with the following command: 
    $ sudo systemctl enable ip6tables.service
    Rule Medium Severity
    Show

  • Verify iptables Enabled

    The iptables service can be enabled with the following command: 
    $ sudo systemctl enable iptables.service
    Rule Medium Severity
    Show

  • Set Default ip6tables Policy for Incoming Packets

    To set the default policy to DROP (instead of ACCEPT) for the built-in INPUT chain which processes incoming packets, add or correct the following l...
    Rule Medium Severity
    Show

  • Set configuration for IPv6 loopback traffic

    Configure the loopback interface to accept traffic. Configure all other interfaces to deny traffic to the loopback network.
    Rule Medium Severity
    Show

  • Set configuration for loopback traffic

    Configure the loopback interface to accept traffic. Configure all other interfaces to deny traffic to the loopback network.
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in the configuration files <co...
    Group
    Show

  • net.ipv4.conf.default.secure_redirects

    Enable to prevent hijacking of routing path by only allowing redirects from gateways known in routing table. Disable to refuse acceptance of secure...
    Value
    Show

  • Set Default iptables Policy for Forwarded Packets

    To set the default policy to DROP (instead of ACCEPT) for the built-in FORWARD chain which processes packets that will be forwarded from one interf...
    Rule Medium Severity
    Show

  • Ensure Outbound and Established Connections are Configured

    Configure the firewall rules for new outbound and established connections.
    Rule Medium Severity
    Show

  • Restrict ICMP Message Types

    In <code>/etc/sysconfig/iptables</code>, the accepted ICMP messages types can be restricted. To accept only ICMP echo reply, destination unreachabl...
    Group
    Show

  • Log and Drop Packets with Suspicious Source Addresses

    Packets with non-routable source addresses should be rejected, as they may indicate spoofing. Because the modified policy will reject non-matching ...
    Group
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the numb...
    Group
    Show

  • Disable Support for IPv6 Unless Needed

    Despite configuration that suggests support for IPv6 has been disabled, link-local IPv6 address auto-configuration occurs even when only an IPv4 ad...
    Group
    Show

  • Ensure IPv6 is disabled through kernel boot parameter

    To disable IPv6 protocol support in the Linux kernel, add the argument <code>ipv6.disable=1</code> to the default GRUB2 command line for the Linux ...
    Rule Low Severity
    Show

  • Disable IPv6 Networking Support Automatic Loading

    To prevent the IPv6 kernel module (<code>ipv6</code>) from binding to the IPv6 networking stack, add the following line to <code>/etc/modprobe.d/di...
    Rule Medium Severity
    Show

  • Disable IPv6 Addressing on All IPv6 Interfaces

    To disable support for (<code>ipv6</code>) addressing on all interface add the following line to <code>/etc/sysctl.d/ipv6.conf</code> (or another f...
    Rule Medium Severity
    Show

  • conman_can_network SELinux Boolean

    default - Default SELinux boolean setting.
    on - SELinux boolean is enabled.
    off - SELinux boolean is disabled.
    Value
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules