Skip to content
ATO Pathways
  Log In

Guide to the Secure Configuration of Red Hat Virtualization 4

Rules, Groups, and Values defined within the XCCDF Benchmark

  • Enable rsyslog to Accept Messages via TCP, if Acting As Log Server

    The <code>rsyslog</code> daemon should not accept remote messages unless the system acts as a log server. If the system needs to act as a central l...
    Rule Unknown Severity
    Show

  • Enable rsyslog to Accept Messages via UDP, if Acting As Log Server

    The <code>rsyslog</code> daemon should not accept remote messages unless the system acts as a log server. If the system needs to act as a central l...
    Rule Unknown Severity
    Show

  • Ensure rsyslog Does Not Accept Remote Messages Unless Acting As Log Server

    The <code>rsyslog</code> daemon should not accept remote messages unless the system acts as a log server. To ensure that it is not listening on the...
    Rule Medium Severity
    Show

  • net.ipv4.conf.default.shared_media

    Controls whether the system can send(router) or accept(host) RFC1620 shared media redirects. <code>shared_media</code> for the interface will be en...
    Value
    Show

  • Rsyslog Logs Sent To Remote Host

    If system logs are to be useful in detecting malicious activities, it is necessary to send logs to a remote server. An intruder who has compromised...
    Group
    Show

  • Remote Log Server

    Specify an URI or IP address of a remote host where the log messages will be sent and stored.
    Value
    Show

  • Ensure Logs Sent To Remote Host

    To configure rsyslog to send logs to a remote log server, open <code>/etc/rsyslog.conf</code> and read and understand the last section of the file,...
    Rule Medium Severity
    Show

  • Network Configuration and Firewalls

    Most systems must be connected to a network of some sort, and this brings with it the substantial risk of network attack. This section discusses th...
    Group
    Show

  • Configure Multiple DNS Servers in /etc/resolv.conf

    Multiple Domain Name System (DNS) Servers should be configured in <code>/etc/resolv.conf</code>. This provides redundant name resolution services ...
    Rule Medium Severity
    Show

  • Prevent non-Privileged Users from Modifying Network Interfaces using nmcli

    By default, non-privileged users are given permissions to modify networking interfaces and configurations using the <code>nmcli</code> command. Non...
    Rule Medium Severity
    Show

  • Ensure System is Not Acting as a Network Sniffer

    The system should not be acting as a network sniffer, which can capture all traffic on the network to which it is connected. Run the following to d...
    Rule Medium Severity
    Show

  • Install iptables Package

    The iptables package can be installed with the following command: 
    $ sudo yum install iptables
    Rule Medium Severity
    Show

  • net.ipv4.icmp_echo_ignore_broadcasts

    Ignore all ICMP ECHO and TIMESTAMP requests sent to it via broadcast/multicast
    Value
    Show

  • firewalld

    The dynamic firewall daemon <code>firewalld</code> provides a dynamically managed firewall with support for network “zones” to assign a level of tr...
    Group
    Show

  • Inspect and Activate Default firewalld Rules

    Firewalls can be used to separate networks into different zones based on the level of trust the user has decided to place on the devices and traffi...
    Group
    Show

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in configuration files under t...
    Group
    Show

  • Configure the Firewalld Ports

    Configure the <code>firewalld</code> ports to allow approved services to have access to the system. To configure <code>firewalld</code> to open por...
    Rule Medium Severity
    Show

  • Set Default firewalld Zone for Incoming Packets

    To set the default zone to <code>drop</code> for the built-in default zone which processes incoming IPv4 and IPv6 packets, modify the following lin...
    Rule Medium Severity
    Show

  • IPSec Support

    Support for Internet Protocol Security (IPsec) is provided with Libreswan.
    Group
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules