Skip to content
ATO Pathways
  Log In

Guide to the Secure Configuration of Red Hat Enterprise Linux 7

Rules, Groups, and Values defined within the XCCDF Benchmark

  • Remove iptables-services Package

    The iptables-services package can be removed with the following command: 
    $ sudo yum erase iptables-services
    Rule Medium Severity
    Show

  • Inspect and Activate Default Rules

    View the currently-enforced <code>iptables</code> rules by running the command: <pre>$ sudo iptables -nL --line-numbers</pre> The command is analog...
    Group
    Show

  • Verify ip6tables Enabled if Using IPv6

    The ip6tables service can be enabled with the following command: 
    $ sudo systemctl enable ip6tables.service
    Rule Medium Severity
    Show

  • net.ipv4.conf.all.shared_media

    Controls whether the system can send (router) or accept (host) RFC1620 shared media redirects. <code>shared_media</code> for the interface will be ...
    Value
    Show

  • Set configuration for IPv6 loopback traffic

    Configure the loopback interface to accept traffic. Configure all other interfaces to deny traffic to the loopback network.
    Rule Medium Severity
    Show

  • Set configuration for loopback traffic

    Configure the loopback interface to accept traffic. Configure all other interfaces to deny traffic to the loopback network.
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in the configuration files <co...
    Group
    Show

  • Ensure ip6tables Firewall Rules Exist for All Open Ports

    Any ports that have been opened on non-loopback addresses need firewall rules to govern traffic.
    Rule Medium Severity
    Show

  • Ensure iptables Firewall Rules Exist for All Open Ports

    Any ports that have been opened on non-loopback addresses need firewall rules to govern traffic.
    Rule Medium Severity
    Show

  • Set Default iptables Policy for Incoming Packets

    To set the default policy to DROP (instead of ACCEPT) for the built-in INPUT chain which processes incoming packets, add or correct the following l...
    Rule Medium Severity
    Show

  • Set Default iptables Policy for Forwarded Packets

    To set the default policy to DROP (instead of ACCEPT) for the built-in FORWARD chain which processes packets that will be forwarded from one interf...
    Rule Medium Severity
    Show

  • Restrict ICMP Message Types

    In <code>/etc/sysconfig/iptables</code>, the accepted ICMP messages types can be restricted. To accept only ICMP echo reply, destination unreachabl...
    Group
    Show

  • net.ipv4.conf.default.accept_redirects

    Disable ICMP Redirect Acceptance?
    Value
    Show

  • Log and Drop Packets with Suspicious Source Addresses

    Packets with non-routable source addresses should be rejected, as they may indicate spoofing. Because the modified policy will reject non-matching ...
    Group
    Show

  • IPv6

    The system includes support for Internet Protocol version 6. A major and often-mentioned improvement over IPv4 is its enormous increase in the numb...
    Group
    Show

  • Disable Support for IPv6 Unless Needed

    Despite configuration that suggests support for IPv6 has been disabled, link-local IPv6 address auto-configuration occurs even when only an IPv4 ad...
    Group
    Show

  • Ensure IPv6 is disabled through kernel boot parameter

    To disable IPv6 protocol support in the Linux kernel, add the argument <code>ipv6.disable=1</code> to the default GRUB2 command line for the Linux ...
    Rule Low Severity
    Show

  • Disable IPv6 Networking Support Automatic Loading

    To prevent the IPv6 kernel module (<code>ipv6</code>) from binding to the IPv6 networking stack, add the following line to <code>/etc/modprobe.d/di...
    Rule Medium Severity
    Show

  • Disable Interface Usage of IPv6

    To disable interface usage of IPv6, add or correct the following lines in <code>/etc/sysconfig/network</code>: <pre>NETWORKING_IPV6=no IPV6INIT=no<...
    Rule Unknown Severity
    Show

  • Disable Support for RPC IPv6

    RPC services for NFSv4 try to load transport modules for <code>udp6</code> and <code>tcp6</code> by default, even if IPv6 has been disabled in <cod...
    Rule Unknown Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules