Skip to content
ATO Pathways
  Log In

Guide to the Secure Configuration of Red Hat Enterprise Linux 7

Rules, Groups, and Values defined within the XCCDF Benchmark

  • Disable Zeroconf Networking

    Zeroconf networking allows the system to assign itself an IP address and engage in IP communication without a statically-assigned address or even a...
    Rule Unknown Severity
    Show

  • Prevent non-Privileged Users from Modifying Network Interfaces using nmcli

    By default, non-privileged users are given permissions to modify networking interfaces and configurations using the <code>nmcli</code> command. Non...
    Rule Medium Severity
    Show

  • Set Default ip6tables Policy for Incoming Packets

    To set the default policy to DROP (instead of ACCEPT) for the built-in INPUT chain which processes incoming packets, add or correct the following l...
    Rule Medium Severity
    Show

  • Ensure System is Not Acting as a Network Sniffer

    The system should not be acting as a network sniffer, which can capture all traffic on the network to which it is connected. Run the following to d...
    Rule Medium Severity
    Show

  • firewalld

    The dynamic firewall daemon <code>firewalld</code> provides a dynamically managed firewall with support for network “zones” to assign a level of tr...
    Group
    Show

  • Ensure network interfaces are assigned to appropriate zone

    Firewall zones define the trust level of network connections or interfaces. Note: Changing firewall settings while connected over network can resul...
    Rule Medium Severity
    Show

  • Inspect and Activate Default firewalld Rules

    Firewalls can be used to separate networks into different zones based on the level of trust the user has decided to place on the devices and traffi...
    Group
    Show

  • Install firewalld Package

    The firewalld package can be installed with the following command: 
    $ sudo yum install firewalld
    Rule Medium Severity
    Show

  • Verify firewalld Enabled

    The firewalld service can be enabled with the following command: 
    $ sudo systemctl enable firewalld.service
    Rule Medium Severity
    Show

  • Strengthen the Default Ruleset

    The default rules can be strengthened. The system scripts that activate the firewall rules expect them to be defined in configuration files under t...
    Group
    Show

  • Configure the Firewalld Ports

    Configure the <code>firewalld</code> ports to allow approved services to have access to the system. To configure <code>firewalld</code> to open por...
    Rule Medium Severity
    Show

  • net.ipv6.conf.default.router_solicitations

    Accept all router solicitations by default?
    Value
    Show

  • net.ipv4.conf.all.secure_redirects

    Enable to prevent hijacking of routing path by only allowing redirects from gateways known in routing table. Disable to refuse acceptance of secure...
    Value
    Show

  • Configure firewalld To Rate Limit Connections

    Create a direct firewall rule to protect against DoS attacks with the following command: <pre>$ sudo firewall-cmd --permanent --direct --add-rule i...
    Rule Medium Severity
    Show

  • Set Default firewalld Zone for Incoming Packets

    To set the default zone to <code>drop</code> for the built-in default zone which processes incoming IPv4 and IPv6 packets, modify the following lin...
    Rule Medium Severity
    Show

  • IPSec Support

    Support for Internet Protocol Security (IPsec) is provided with Libreswan.
    Group
    Show

  • Install libreswan Package

    The libreswan package provides an implementation of IPsec and IKE, which permits the creation of secure tunnels over untrusted networks. The <code>...
    Rule Medium Severity
    Show

  • Verify Any Configured IPSec Tunnel Connections

    Libreswan provides an implementation of IPsec and IKE, which permits the creation of secure tunnels over untrusted networks. As such, IPsec can be ...
    Rule Medium Severity
    Show

  • iptables and ip6tables

    A host-based firewall called <code>netfilter</code> is included as part of the Linux kernel distributed with the system. It is activated by default...
    Group
    Show

  • Install iptables Package

    The iptables package can be installed with the following command: 
    $ sudo yum install iptables
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules