Skip to content

Guide to the Secure Configuration of Oracle Linux 8

Rules, Groups, and Values defined within the XCCDF Benchmark

  • Enable Kernel Parameter to Use TCP RFC 1337 on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.tcp_rfc1337</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.tcp_...
    Rule Medium Severity
  • Enable Kernel Parameter to Use TCP Syncookies on Network Interfaces

    To set the runtime status of the <code>net.ipv4.tcp_syncookies</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.t...
    Rule Medium Severity
  • Network Parameters for Hosts Only

    If the system is not going to be used as a router, then setting certain kernel parameters ensure that the host will not perform routing of network ...
    Group
  • Disable Kernel Parameter for Sending ICMP Redirects on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.send_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w n...
    Rule Medium Severity
  • Disable Kernel Parameter for Sending ICMP Redirects on all IPv4 Interfaces by Default

    To set the runtime status of the <code>net.ipv4.conf.default.send_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl ...
    Rule Medium Severity
  • Disable Kernel Parameter for IP Forwarding on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.ip_forward</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.ip_fo...
    Rule Medium Severity
  • nftables

    <code>If firewalld or iptables are being used in your environment, please follow the guidance in their respective section and pass-over the guidanc...
    Group
  • daemons_dump_core SELinux Boolean

    default - Default SELinux boolean setting.
    on - SELinux boolean is enabled.
    off - SELinux boolean is disabled.
    Value
  • daemons_enable_cluster_mode SELinux Boolean

    default - Default SELinux boolean setting.
    on - SELinux boolean is enabled.
    off - SELinux boolean is disabled.
    Value
  • Nftables Base Chain Hooks

    The possible hooks which can be used to configure the base chain are: <code>ingress</code> (only in netdev family since Linux kernel 4.2, and inet ...
    Value
  • Nftables Chain Names

    The rules in nftables are attached to chains. Unlike in iptables, there are no predefined chains like INPUT, OUTPUT, etc. Instead, to filter pack...
    Value
  • Nftables Base Chain Policies

    This is the default verdict that will be applied to packets reaching the end of the chain (i.e, no more rules to be evaluated against). Currently ...
    Value
  • Nftables Base Chain Priorities

    Each nftables base chain is assigned a priority that defines its ordering among other base chains, flowtables, and Netfilter internal operations a...
    Value
  • Nftables Base Chain Types

    Base chains are those that are registered into the Netfilter hooks, i.e. these chains see packets flowing through the Linux TCP/IP stack. The poss...
    Value
  • Nftables Families

    Netfilter enables filtering at multiple networking levels. With iptables there is a separate tool for each level: iptables, ip6tables, arptables, ...
    Value
  • Nftables Master configuration file

    The file which contains top level configuration for nftables service, and with which, the service is started.
    Value
  • Nftables Tables

    Tables in nftables hold chains. Each table only has one address family and only applies to packets of this family. Tables can have one of six fami...
    Value
  • SuSEfirewall2

    The SuSEfirewall2 provides a managed firewall.
    Group
  • Uncomplicated Firewall (ufw)

    The Linux kernel in Ubuntu provides a packet filtering system called netfilter, and the traditional interface for manipulating netfilter are the ip...
    Group
  • Disable ATM Support

    The Asynchronous Transfer Mode (ATM) is a protocol operating on network, data link, and physical layers, based on virtual circuits and virtual path...
    Rule Medium Severity

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules