Juniper Router RTR Security Technical Implementation Guide
Rules, Groups, and Values defined within the XCCDF Benchmark
-
The Juniper perimeter router must be configured to only allow incoming communications from authorized sources to be routed to authorized destinations.
Unrestricted traffic may contain malicious traffic that poses a threat to an enclave or to other connected networks. Additionally, unrestricted traffic may transit a network, which uses bandwidth a...Rule Medium Severity -
The Juniper perimeter router must be configured to protect an enclave connected to an approved gateway by using an inbound filter that only permits packets with destination addresses within the site's address space.
Enclaves with approved gateway connections must take additional steps to ensure there is no compromise on the enclave network or NIPRNet. Without verifying the destination address of traffic coming...Rule High Severity -
The Juniper perimeter router must be configured to restrict it from accepting outbound IP packets that contain an illegitimate address in the source address field via egress filter or by enabling Unicast Reverse Path Forwarding (uRPF).
A compromised host in an enclave can be used by a malicious platform to launch cyberattacks on third parties. This is a common practice in "botnets", which are a collection of compromised computers...Rule High Severity -
The Juniper perimeter router must be configured to filter egress traffic at the internal interface on an inbound direction.
Access lists are used to separate data traffic into that which it will route (permitted packets) and that which it will not route (denied packets). Secure configuration of routers makes use of acce...Rule Medium Severity -
The Juniper perimeter router must be configured to block all packets with any IP options.
Packets with IP options are not fast switched and henceforth must be punted to the router processor. Hackers who initiate denial-of-service (DoS) attacks on routers commonly send large streams of p...Rule Medium Severity -
The Juniper out-of-band management (OOBM) gateway router must be configured to transport management traffic to the Network Operations Center (NOC) via dedicated circuit, MPLS/VPN service, or IPsec tunnel.
Using dedicated paths, the OOBM backbone connects the OOBM gateway routers located at the edge of the managed network and at the NOC. Dedicated links can be deployed using provisioned circuits or M...Rule Medium Severity -
The Juniper router must be configured to only permit management traffic that ingresses and egresses the OOBM interface.
The OOBM access switch will connect to the management interface of the managed network elements. The management interface can be a true OOBM interface or a standard interface functioning as the man...Rule Medium Severity -
The Juniper BGP router must be configured to reject inbound route advertisements for any prefixes belonging to the local autonomous system (AS).
Accepting route advertisements belonging to the local AS can result in traffic looping or being black holed, or at a minimum using a non-optimized path.Rule Medium Severity -
The Juniper BGP router must be configured to reject inbound route advertisements from a customer edge (CE) Juniper router for prefixes that are not allocated to that customer.
As a best practice, a service provider should only accept customer prefixes that have been assigned to that customer and any peering autonomous systems. A multi-homed customer with BGP speaking rou...Rule Medium Severity -
The Juniper BGP router must be configured to reject outbound route advertisements for any prefixes belonging to the IP core.
Outbound route advertisements belonging to the core can result in traffic either looping or being black holed, or at a minimum, using a non-optimized path.Rule Medium Severity -
The Juniper BGP router must be configured to use the maximum prefixes feature to protect against route table flooding and prefix de-aggregation attacks.
The effects of prefix de-aggregation can degrade router performance due to the size of routing tables and also result in black-holing legitimate traffic. Initiated by an attacker or a misconfigured...Rule Medium Severity -
The Juniper BGP router must be configured to use its loopback address as the source address for iBGP peering sessions.
Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of the BGP routers. It is easier to construct appropriate ingress filters...Rule Low Severity -
The Juniper MPLS router must be configured to synchronize IGP and LDP to minimize packet loss when an IGP adjacency is established prior to LDP peers completing label exchange.
Packet loss can occur when an IGP adjacency is established and the router begins forwarding packets using the new adjacency before the LDP label exchange completes between the peers on that link. P...Rule Low Severity -
The Juniper MPLS router must be configured to have TTL Propagation disabled.
The head end of the label-switched path (LSP), the label edge router (LER) will decrement the IP packet's time-to-live (TTL) value by one and then copy the value to the MPLS TTL field. At each labe...Rule Medium Severity -
The Juniper PE router must be configured to have each Virtual Routing and Forwarding (VRF) instance bound to the appropriate physical or logical interfaces to maintain traffic separation between all MPLS L3VPNs.
The primary security model for an MPLS L3VPN infrastructure is traffic separation. The service provider must guarantee the customer that traffic from one VPN does not leak into another VPN or into ...Rule High Severity -
The Juniper PE router providing MPLS Virtual Private Wire Service (VPWS) must be configured to have the appropriate virtual circuit identification (VC ID) for each attachment circuit.
VPWS is an L2VPN technology that provides a virtual circuit between two PE routers to forward Layer 2 frames between two customer-edge routers or switches through an MPLS-enabled IP core. The ingre...Rule High Severity -
The Juniper PE router must be configured to limit the number of MAC addresses it can learn for each Virtual Private LAN Services (VPLS) bridge domain.
VPLS defines an architecture that delivers Ethernet multipoint services over an MPLS network. Customer Layer 2 frames are forwarded across the MPLS core via pseudowires using IEEE 802.1q Ethernet b...Rule Medium Severity -
The Juniper PE router must be configured to enforce a Quality-of-Service (QoS) policy in accordance with the QoS GIG Technical Profile.
Different applications have unique requirements and toleration levels for delay, jitter, bandwidth, packet loss, and availability. To manage the multitude of applications and services, a network re...Rule Low Severity -
The Juniper multicast router must be configured to bind a Protocol Independent Multicast (PIM) neighbor filter to interfaces that have PIM enabled.
PIM is a routing protocol used to build multicast distribution trees for forwarding multicast traffic across the network infrastructure. PIM traffic must be limited to only known PIM neighbors by c...Rule Medium Severity -
The Juniper multicast Rendezvous Point (RP) router must be configured to filter Protocol Independent Multicast (PIM) Register messages received from the Designated Router (DR) for any undesirable multicast groups and sources.
Real-time multicast traffic can entail multiple large flows of data. An attacker can flood a network segment with multicast packets, over-using the available bandwidth and thereby creating a denial...Rule Low Severity
Node 2
The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.