Skip to content
Log In

Guide to the Secure Configuration of Alibaba Cloud Linux 2

Rules, Groups, and Values defined within the XCCDF Benchmark

  • Configure IPv6 Settings if Necessary

    A major feature of IPv6 is the extent to which systems implementing it can automatically configure their networking devices using information from the network. From a security perspective, manually...
    Group
    Show

  • net.ipv6.conf.default.accept_source_route

    Trackers could be using source-routed packets to generate traffic that seems to be intra-net, but actually was created outside and has been redirected.
    Value
    Show

  • net.ipv4.conf.default.arp_filter

    Controls whether the ARP filter is enabled or not. 1 - Allows you to have multiple network interfaces on the same subnet, and have the ARPs for each interface be answered based on whether or not t...
    Value
    Show

  • net.ipv4.conf.default.arp_ignore

    Control the response modes for ARP queries that resolve local target IP addresses: 0 - (default): reply for any local target IP address, configured on any interface 1 - reply only if the target IP...
    Value
    Show

  • net.ipv4.conf.all.rp_filter

    Enable to enforce sanity checking, also called ingress filtering or egress filtering. The point is to drop a packet if the source and destination IP addresses in the IP header do not make sense whe...
    Value
    Show

  • net.ipv4.conf.all.secure_redirects

    Enable to prevent hijacking of routing path by only allowing redirects from gateways known in routing table. Disable to refuse acceptance of secure ICMP redirected packets on all interfaces.
    Value
    Show

  • net.ipv4.conf.all.shared_media

    Controls whether the system can send (router) or accept (host) RFC1620 shared media redirects. <code>shared_media</code> for the interface will be enabled if at least one of conf/{all,interface}/sh...
    Value
    Show

  • net.ipv4.conf.default.accept_redirects

    Disable ICMP Redirect Acceptance?
    Value
    Show

  • net.ipv4.conf.default.shared_media

    Controls whether the system can send(router) or accept(host) RFC1620 shared media redirects. <code>shared_media</code> for the interface will be enabled if at least one of conf/{all,interface}/shar...
    Value
    Show

  • net.ipv4.icmp_echo_ignore_broadcasts

    Ignore all ICMP ECHO and TIMESTAMP requests sent to it via broadcast/multicast
    Value
    Show

  • net.ipv4.icmp_ignore_bogus_error_responses

    Enable to prevent unnecessary logging
    Value
    Show

  • net.ipv4.tcp_syncookies

    Enable to turn on TCP SYN Cookie Protection
    Value
    Show

  • Configure Response Mode of ARP Requests for All IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.arp_ignore</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.arp_ignore=<xccdf-1.2:sub idref="xccd...
    Rule Medium Severity
    Show

  • Prevent Routing External Traffic to Local Loopback on All IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.route_localnet</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.route_localnet=0</pre> To make su...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Use Reverse Path Filtering on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.rp_filter</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.rp_filter=1</pre> To make sure that th...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting Secure ICMP Redirects on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.secure_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.secure_redirects=0</pre> To mak...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.default.accept_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.accept_redirects=0</pre...
    Rule Medium Severity
    Show

  • Configure Sending and Accepting Shared Media Redirects by Default

    To set the runtime status of the <code>net.ipv4.conf.default.shared_media</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.default.shared_media=<xccdf-1.2:sub...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Ignore ICMP Broadcast Echo Requests on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.icmp_echo_ignore_broadcasts</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.icmp_echo_ignore_broadcasts=1</pre> To...
    Rule Medium Severity
    Show

  • Network Parameters for Hosts Only

    If the system is not going to be used as a router, then setting certain kernel parameters ensure that the host will not perform routing of network traffic.
    Group
    Show

  • Disable Kernel Parameter for Sending ICMP Redirects on all IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.conf.all.send_redirects</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.conf.all.send_redirects=0</pre> To make su...
    Rule Medium Severity
    Show

  • Disable Kernel Parameter for IP Forwarding on IPv4 Interfaces

    To set the runtime status of the <code>net.ipv4.ip_forward</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w net.ipv4.ip_forward=0</pre> To make sure that the setting is per...
    Rule Medium Severity
    Show

  • Uncomplicated Firewall (ufw)

    The Linux kernel in Ubuntu provides a packet filtering system called netfilter, and the traditional interface for manipulating netfilter are the iptables suite of commands. iptables provide a compl...
    Group
    Show

  • Verify ufw Enabled

    The ufw service can be enabled with the following command: 
    $ sudo systemctl enable ufw.service
    Rule Medium Severity
    Show

  • Uncommon Network Protocols

    The system includes support for several network protocols which are not commonly used. Although security vulnerabilities in kernel networking code are not frequently discovered, the consequences ca...
    Group
    Show

  • Disable DCCP Support

    The Datagram Congestion Control Protocol (DCCP) is a relatively new transport layer protocol, designed to support streaming media and telephony. To configure the system to prevent the <code>dccp</...
    Rule Medium Severity
    Show

  • Verify Permissions on Important Files and Directories

    Permissions for many files on a system must be set restrictively to ensure sensitive information is properly protected. This section discusses important permission restrictions which can be verifie...
    Group
    Show

  • Enable Kernel Parameter to Enforce DAC on Hardlinks

    To set the runtime status of the <code>fs.protected_hardlinks</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w fs.protected_hardlinks=1</pre> To make sure that the setting ...
    Rule Medium Severity
    Show

  • Enable Kernel Parameter to Enforce DAC on Symlinks

    To set the runtime status of the <code>fs.protected_symlinks</code> kernel parameter, run the following command: <pre>$ sudo sysctl -w fs.protected_symlinks=1</pre> To make sure that the setting is...
    Rule Medium Severity
    Show

  • Verify Permissions on Files with Local Account Information and Credentials

    The default restrictive permissions for files which act as important security databases such as <code>passwd</code>, <code>shadow</code>, <code>group</code>, and <code>gshadow</code> files must be ...
    Group
    Show

  • Verify Group Who Owns Backup group File

    To properly set the group owner of /etc/group-, run the command: 
    $ sudo chgrp root /etc/group-
    Rule Medium Severity
    Show

  • Verify User Who Owns Backup shadow File

    To properly set the group owner of /etc/shadow-, run the command: 
    $ sudo chgrp root /etc/shadow-
    Rule Medium Severity
    Show

  • Verify Group Who Owns group File

    To properly set the group owner of /etc/group, run the command: 
    $ sudo chgrp root /etc/group
    Rule Medium Severity
    Show

  • Verify Group Who Owns passwd File

    To properly set the group owner of /etc/passwd, run the command: 
    $ sudo chgrp root /etc/passwd
    Rule Medium Severity
    Show

  • Verify Group Who Owns shadow File

    To properly set the group owner of /etc/shadow, run the command: 
    $ sudo chgrp root /etc/shadow
    Rule Medium Severity
    Show

  • Verify User Who Owns Backup group File

    To properly set the owner of /etc/group-, run the command: 
    $ sudo chown root /etc/group-
    Rule Medium Severity
    Show

  • Verify User Who Owns Backup passwd File

    To properly set the owner of /etc/passwd-, run the command: 
    $ sudo chown root /etc/passwd-
    Rule Medium Severity
    Show

  • Verify Group Who Owns Backup shadow File

    To properly set the owner of /etc/shadow-, run the command: 
    $ sudo chown root /etc/shadow-
    Rule Medium Severity
    Show

  • Verify User Who Owns group File

    To properly set the owner of /etc/group, run the command: 
    $ sudo chown root /etc/group
    Rule Medium Severity
    Show

  • Verify User Who Owns passwd File

    To properly set the owner of /etc/passwd, run the command: 
    $ sudo chown root /etc/passwd
    Rule Medium Severity
    Show

  • Verify User Who Owns shadow File

    To properly set the owner of /etc/shadow, run the command: 
    $ sudo chown root /etc/shadow
    Rule Medium Severity
    Show

  • Verify Permissions on Backup group File

    To properly set the permissions of /etc/group-, run the command: 
    $ sudo chmod 0644 /etc/group-
    Rule Medium Severity
    Show

  • Verify Permissions on Backup shadow File

    To properly set the permissions of /etc/shadow-, run the command: 
    $ sudo chmod 0000 /etc/shadow-
    Rule Medium Severity
    Show

  • Verify Permissions on /var/log/messages File

    To properly set the permissions of /var/log/messages, run the command: 
    $ sudo chmod 0640 /var/log/messages
    Rule Medium Severity
    Show

  • Verify File Permissions Within Some Important Directories

    Some directories contain files whose confidentiality or integrity is notably important and may also be susceptible to misconfiguration over time, particularly if unpackaged software is installed. A...
    Group
    Show

  • Verify that Shared Library Directories Have Root Ownership

    System-wide shared library files, which are linked to executables during process load time or run time, are stored in the following directories by default: <pre>/lib /lib64 /usr/lib /usr/lib64 </pr...
    Rule Medium Severity
    Show

  • Verify that System Executable Directories Have Restrictive Permissions

    System executables are stored in the following directories by default: <pre>/bin /sbin /usr/bin /usr/sbin /usr/local/bin /usr/local/sbin</pre> These directories should not be group-writable or worl...
    Rule Medium Severity
    Show

  • Verify that System Executables Have Root Ownership

    System executables are stored in the following directories by default: <pre>/bin /sbin /usr/bin /usr/libexec /usr/local/bin /usr/local/sbin /usr/sbin</pre> All files in these directories should be ...
    Rule Medium Severity
    Show

  • Verify that Shared Library Files Have Root Ownership

    System-wide shared library files, which are linked to executables during process load time or run time, are stored in the following directories by default: <pre>/lib /lib64 /usr/lib /usr/lib64 </pr...
    Rule Medium Severity
    Show

  • Verify that System Executables Have Restrictive Permissions

    System executables are stored in the following directories by default: <pre>/bin /sbin /usr/bin /usr/libexec /usr/local/bin /usr/local/sbin /usr/sbin</pre> All files in these directories should not...
    Rule Medium Severity
    Show

Node 2

siemur/test-space

The content of the drawer really is up to you. It could have form fields, definition lists, text lists, labels, charts, progress bars, etc. Spacing recommendation is 24px margins. You can put tabs in here, and can also make the drawer scrollable.

Capacity
Modules